1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
|
// file: clkmgr_dcm_tb.v
//
// (c) Copyright 2008 - 2011 Xilinx, Inc. All rights reserved.
//
// This file contains confidential and proprietary information
// of Xilinx, Inc. and is protected under U.S. and
// international copyright and other intellectual property
// laws.
//
// DISCLAIMER
// This disclaimer is not a license and does not grant any
// rights to the materials distributed herewith. Except as
// otherwise provided in a valid license issued to you by
// Xilinx, and to the maximum extent permitted by applicable
// law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// (2) Xilinx shall not be liable (whether in contract or tort,
// including negligence, or under any other theory of
// liability) for any loss or damage of any kind or nature
// related to, arising under or in connection with these
// materials, including for any direct, or any indirect,
// special, incidental, or consequential loss or damage
// (including loss of data, profits, goodwill, or any type of
// loss or damage suffered as a result of any action brought
// by a third party) even if such damage or loss was
// reasonably foreseeable or Xilinx had been advised of the
// possibility of the same.
//
// CRITICAL APPLICATIONS
// Xilinx products are not designed or intended to be fail-
// safe, or for use in any application requiring fail-safe
// performance, such as life-support or safety devices or
// systems, Class III medical devices, nuclear facilities,
// applications related to the deployment of airbags, or any
// other applications that could lead to death, personal
// injury, or severe property or environmental damage
// (individually and collectively, "Critical
// Applications"). Customer assumes the sole risk and
// liability of any use of Xilinx products in Critical
// Applications, subject only to applicable laws and
// regulations governing limitations on product liability.
//
// THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// PART OF THIS FILE AT ALL TIMES.
//
//----------------------------------------------------------------------------
// Clocking wizard demonstration testbench
//----------------------------------------------------------------------------
// This demonstration testbench instantiates the example design for the
// clocking wizard. Input clocks are toggled, which cause the clocking
// network to lock and the counters to increment.
//----------------------------------------------------------------------------
`timescale 1ps/1ps
`define wait_lock @(posedge CLK_VALID)
module clkmgr_dcm_tb ();
// Clock to Q delay of 100ps
localparam TCQ = 100;
// timescale is 1ps/1ps
localparam ONE_NS = 1000;
localparam PHASE_ERR_MARGIN = 100; // 100ps
// how many cycles to run
localparam COUNT_PHASE = 1024;
// we'll be using the period in many locations
localparam time PER1 = 20.0*ONE_NS;
localparam time PER1_1 = PER1/2;
localparam time PER1_2 = PER1 - PER1/2;
// Declare the input clock signals
reg CLK_IN1 = 1;
// The high bit of the sampling counter
wire COUNT;
// Status and control signals
reg RESET = 0;
wire INPUT_CLK_STOPPED;
wire CLK_VALID;
reg COUNTER_RESET = 0;
wire [1:1] CLK_OUT;
//Freq Check using the M & D values setting and actual Frequency generated
// Input clock generation
//------------------------------------
always begin
CLK_IN1 = #PER1_1 ~CLK_IN1;
CLK_IN1 = #PER1_2 ~CLK_IN1;
end
// Test sequence
reg [15*8-1:0] test_phase = "";
initial begin
// Set up any display statements using time to be readable
$timeformat(-12, 2, "ps", 10);
COUNTER_RESET = 0;
test_phase = "reset";
RESET = 1;
#(PER1*6);
RESET = 0;
test_phase = "wait lock";
`wait_lock;
#(PER1*6);
COUNTER_RESET = 1;
#(PER1*20)
COUNTER_RESET = 0;
test_phase = "counting";
#(PER1*COUNT_PHASE);
$display("SIMULATION PASSED");
$display("SYSTEM_CLOCK_COUNTER : %0d\n",$time/PER1);
$finish;
end
// Instantiation of the example design containing the clock
// network and sampling counters
//---------------------------------------------------------
clkmgr_dcm_exdes
#(
.TCQ (TCQ)
) dut
(// Clock in ports
.CLK_IN1 (CLK_IN1),
// Reset for logic in example design
.COUNTER_RESET (COUNTER_RESET),
.CLK_OUT (CLK_OUT),
// High bits of the counters
.COUNT (COUNT),
// Status and control signals
.RESET (RESET),
.INPUT_CLK_STOPPED (INPUT_CLK_STOPPED),
.CLK_VALID (CLK_VALID));
// Freq Check
endmodule
|
