1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
|
// file: clkmgr_dcm_exdes.v
//
// (c) Copyright 2008 - 2011 Xilinx, Inc. All rights reserved.
//
// This file contains confidential and proprietary information
// of Xilinx, Inc. and is protected under U.S. and
// international copyright and other intellectual property
// laws.
//
// DISCLAIMER
// This disclaimer is not a license and does not grant any
// rights to the materials distributed herewith. Except as
// otherwise provided in a valid license issued to you by
// Xilinx, and to the maximum extent permitted by applicable
// law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// (2) Xilinx shall not be liable (whether in contract or tort,
// including negligence, or under any other theory of
// liability) for any loss or damage of any kind or nature
// related to, arising under or in connection with these
// materials, including for any direct, or any indirect,
// special, incidental, or consequential loss or damage
// (including loss of data, profits, goodwill, or any type of
// loss or damage suffered as a result of any action brought
// by a third party) even if such damage or loss was
// reasonably foreseeable or Xilinx had been advised of the
// possibility of the same.
//
// CRITICAL APPLICATIONS
// Xilinx products are not designed or intended to be fail-
// safe, or for use in any application requiring fail-safe
// performance, such as life-support or safety devices or
// systems, Class III medical devices, nuclear facilities,
// applications related to the deployment of airbags, or any
// other applications that could lead to death, personal
// injury, or severe property or environmental damage
// (individually and collectively, "Critical
// Applications"). Customer assumes the sole risk and
// liability of any use of Xilinx products in Critical
// Applications, subject only to applicable laws and
// regulations governing limitations on product liability.
//
// THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// PART OF THIS FILE AT ALL TIMES.
//
//----------------------------------------------------------------------------
// Clocking wizard example design
//----------------------------------------------------------------------------
// This example design instantiates the created clocking network, where each
// output clock drives a counter. The high bit of each counter is ported.
//----------------------------------------------------------------------------
`timescale 1ps/1ps
module clkmgr_dcm_exdes
#(
parameter TCQ = 100
)
(// Clock in ports
input CLK_IN1,
// Reset that only drives logic in example design
input COUNTER_RESET,
output [1:1] CLK_OUT,
// High bits of counters driven by clocks
output COUNT,
// Status and control signals
input RESET,
output INPUT_CLK_STOPPED,
output CLK_VALID
);
// Parameters for the counters
//-------------------------------
// Counter width
localparam C_W = 16;
// Create reset for the counters
wire reset_int = RESET || COUNTER_RESET;
reg rst_sync;
reg rst_sync_int;
reg rst_sync_int1;
reg rst_sync_int2;
// Declare the clocks and counter
wire clk_int;
wire clk_n;
wire clk;
reg [C_W-1:0] counter;
// Insert BUFGs on all input clocks that don't already have them
//--------------------------------------------------------------
BUFG clkin1_buf
(.O (clk_in1_buf),
.I (CLK_IN1));
// Instantiation of the clocking network
//--------------------------------------
clkmgr_dcm clknetwork
(// Clock in ports
.CLK_IN1 (clk_in1_buf),
// Clock out ports
.CLK_OUT1 (clk_int),
// Status and control signals
.RESET (RESET),
.INPUT_CLK_STOPPED (INPUT_CLK_STOPPED),
.CLK_VALID (CLK_VALID));
assign clk_n = ~clk;
ODDR2 clkout_oddr
(.Q (CLK_OUT[1]),
.C0 (clk),
.C1 (clk_n),
.CE (1'b1),
.D0 (1'b1),
.D1 (1'b0),
.R (1'b0),
.S (1'b0));
// Connect the output clocks to the design
//-----------------------------------------
assign clk = clk_int;
// Reset synchronizer
//-----------------------------------
always @(posedge reset_int or posedge clk) begin
if (reset_int) begin
rst_sync <= 1'b1;
rst_sync_int <= 1'b1;
rst_sync_int1 <= 1'b1;
rst_sync_int2 <= 1'b1;
end
else begin
rst_sync <= 1'b0;
rst_sync_int <= rst_sync;
rst_sync_int1 <= rst_sync_int;
rst_sync_int2 <= rst_sync_int1;
end
end
// Output clock sampling
//-----------------------------------
always @(posedge clk or posedge rst_sync_int2) begin
if (rst_sync_int2) begin
counter <= #TCQ { C_W { 1'b 0 } };
end else begin
counter <= #TCQ counter + 1'b 1;
end
end
// alias the high bit to the output
assign COUNT = counter[C_W-1];
endmodule
|
