//======================================================================
//
// novena_baseline_top.v
// ---------------------
// Top module for the Cryptech Novena FPGA framework. This design
// allow us to run the EIM interface at one clock and cores including
// core selector with the always present global clock.
//
//
// Author: Pavel Shatov
// Copyright (c) 2014, NORDUnet A/S All rights reserved.
//
// Redistribution and use in source and binary forms, with or without
// modification, are permitted provided that the following conditions
// are met:
// - Redistributions of source code must retain the above copyright
// notice, this list of conditions and the following disclaimer.
//
// - Redistributions in binary form must reproduce the above copyright
// notice, this list of conditions and the following disclaimer in the
// documentation and/or other materials provided with the distribution.
//
// - Neither the name of the NORDUnet nor the names of its contributors may
// be used to endorse or promote products derived from this software
// without specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
// IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
// TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
// PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
// HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
// SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
// TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
// PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
// LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
// NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
// SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
//
//======================================================================
module novena_baseline_top
(
// Differential input for 50 MHz general clock.
input wire gclk_p_pin,
input wire gclk_n_pin,
// Reset controlled by the CPU.
// this must be configured as input w/pullup
input wire reset_mcu_b_pin,
// Cryptech avalanche noise board input and LED outputs
input wire ct_noise,
output wire [07 : 0] ct_led,
// EIM interface
input wire eim_bclk, // EIM burst clock. Started by the CPU.
input wire eim_cs0_n, // Chip select (active low).
inout wire [15 : 0] eim_da, // Bidirectional address and data port.
input wire [18: 16] eim_a, // MSB part of address port.
input wire eim_lba_n, // Latch address signal (active low).
input wire eim_wr_n, // write enable signal (active low).
input wire eim_oe_n, // output enable signal (active low).
output wire eim_wait_n, // Data wait signal (active low).
// Novena utility ports
apoptosis_pin, // Hold low to not restart after config.
led_pin // LED on edge close to the FPGA.
);
//----------------------------------------------------------------
// Clock Manager
//
// Clock manager is used to buffer BCLK, generate SYS_CLK
// from GCLK and implement the reset logic.
//----------------------------------------------------------------
wire sys_clk;
wire sys_rst;
wire eim_bclk_buf;
novena_clkmgr clkmgr
(
.gclk_p(gclk_p_pin),
.gclk_n(gclk_n_pin),
.reset_mcu_b(reset_mcu_b_pin),
.sys_clk(sys_clk),
.sys_rst(sys_rst),
.bclk_in(eim_bclk),
.bclk_out(eim_bclk_buf)
);
//----------------------------------------------------------------
// EIM Arbiter
//
// EIM arbiter handles EIM access and transfers it into
// `sys_clk' clock domain.
//----------------------------------------------------------------
wire [16: 0] sys_eim_addr;
wire sys_eim_wr;
wire sys_eim_rd;
wire [31: 0] sys_eim_dout;
wire [31: 0] sys_eim_din;
eim_arbiter eim
(
.eim_bclk(eim_bclk_buf),
.eim_cs0_n(eim_cs0_n),
.eim_da(eim_da),
.eim_a(eim_a),
.eim_lba_n(eim_lba_n),
.eim_wr_n(eim_wr_n),
.eim_oe_n(eim_oe_n),
.eim_wait_n(eim_wait_n),
.sys_clk(sys_clk),
.sys_addr(sys_eim_addr),
.sys_wren(sys_eim_wr),
.sys_data_out(sys_eim_dout),
.sys_rden(sys_eim_rd),
.sys_data_in(sys_eim_din)
);
//----------------------------------------------------------------
// Memory Mapper
//
// This multiplexer is used to map different types of cores, such as
// hashes, RNGs and ciphers to different regions (segments) of memory.
//----------------------------------------------------------------
eim_memory mem
(
.sys_clk(sys_clk),
.sys_rst(sys_rst),
.sys_eim_addr(sys_eim_addr),
.sys_eim_wr(sys_eim_wr),
.sys_eim_rd(sys_eim_rd),
.sys_write_data(sys_eim_dout),
.sys_read_data(sys_eim_din)
);
//----------------------------------------------------------------
// LED Driver
//
// A simple utility LED driver that turns on the Novena
// board LED when the EIM interface is active.
//----------------------------------------------------------------
eim_indicator led
(
.sys_clk(sys_clk),
.sys_rst(sys_rst),
.eim_active(sys_eim_wr | sys_eim_rd),
.led_out(led_pin)
);
//----------------------------------------------------------------
// Cryptech Logic
//
// Logic specific to the Cryptech use of the Novena.
// Currently we just hard wire the LED outputs.
//----------------------------------------------------------------
assign ct_led = {8{ct_noise}};
//----------------------------------------------------------------
// Novena Patch
//
// Patch logic to keep the Novena board happy.
// The apoptosis_pin pin must be kept low or the whole board
// (more exactly the CPU) will be reset after the FPGA has
// been configured.
//----------------------------------------------------------------
assign apoptosis_pin = 1'b0;
endmodule
//======================================================================
// EOF novena_baseline_top.v
//======================================================================
