/**
******************************************************************************
* File Name : main.c
* Date : 08/07/2015 17:46:00
* Description : Main program body
******************************************************************************
*
* COPYRIGHT(c) 2015 STMicroelectronics
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm-init.h"
#ifdef HAL_GPIO_MODULE_ENABLED
#include "stm-led.h"
#endif
#ifdef HAL_UART_MODULE_ENABLED
#include "stm-uart.h"
#endif
#ifdef HAL_I2C_MODULE_ENABLED
#include "stm-rtc.h"
#endif
#ifdef HAL_SPI_MODULE_ENABLED
#include "stm-fpgacfg.h"
#include "stm-keystore.h"
#endif
#ifdef HAL_SRAM_MODULE_ENABLED
#include "stm-fmc.h"
#endif
#ifdef HAL_SDRAM_MODULE_ENABLED
#include "stm-sdram.h"
#endif
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
#ifdef HAL_GPIO_MODULE_ENABLED
static void MX_GPIO_Init(void);
#endif
void stm_init(void)
{
/* MCU Configuration----------------------------------------------------------*/
/* System interrupt init*/
/* Sets the priority grouping field */
HAL_NVIC_SetPriorityGrouping(NVIC_PRIORITYGROUP_0);
/* Initialize all configured peripherals */
#ifdef HAL_GPIO_MODULE_ENABLED
MX_GPIO_Init();
#endif
#ifdef HAL_UART_MODULE_ENABLED
uart_init();
#endif
#ifdef HAL_I2C_MODULE_ENABLED
rtc_init();
#endif
#ifdef HAL_SPI_MODULE_ENABLED
fpgacfg_init();
keystore_init();
#endif
#ifdef TARGET_CRYPTECH_DEV_BRIDGE
// Blink blue LED for six seconds to not upset the Novena at boot.
led_on(LED_BLUE);
for (int i = 0; i < 12; i++) {
HAL_Delay(500);
led_toggle(LED_BLUE);
}
led_off(LED_BLUE);
#endif
#ifdef HAL_SRAM_MODULE_ENABLED
fmc_init();
#endif
#ifdef HAL_SDRAM_MODULE_ENABLED
sdram_init();
#endif
}
#ifdef HAL_GPIO_MODULE_ENABLED
/* Configure General Purpose Input/Output pins */
static void MX_GPIO_Init(void)
{
/* GPIO Ports Clock Enable */
LED_CLK_ENABLE();
/* Configure LED GPIO pins */
gpio_output(LED_PORT, LED_RED | LED_YELLOW | LED_GREEN | LED_BLUE, GPIO_PIN_RESET);
}
#endif
/**
* @brief This function is executed in case of error occurrence.
* @param None
* @retval None
*/
void Error_Handler(void)
{
#ifdef HAL_GPIO_MODULE_ENABLED
HAL_GPIO_WritePin(LED_PORT, LED_RED, GPIO_PIN_SET);
#endif
while (1) { ; }
}
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
