diff options
Diffstat (limited to 'raw-wiki-dump/GitRepositories%2Fuser%2Fln5%2Fstm32-avalanche-noise.md')
| -rw-r--r-- | raw-wiki-dump/GitRepositories%2Fuser%2Fln5%2Fstm32-avalanche-noise.md | 177 |
1 files changed, 0 insertions, 177 deletions
diff --git a/raw-wiki-dump/GitRepositories%2Fuser%2Fln5%2Fstm32-avalanche-noise.md b/raw-wiki-dump/GitRepositories%2Fuser%2Fln5%2Fstm32-avalanche-noise.md deleted file mode 100644 index 64995ef..0000000 --- a/raw-wiki-dump/GitRepositories%2Fuser%2Fln5%2Fstm32-avalanche-noise.md +++ /dev/null @@ -1,177 +0,0 @@ -``` -#!htmlcomment - -This page is maintained automatically by a script. Don't modify this page by hand, -your changes will just be overwritten the next time the script runs. Talk to your -Friendly Neighborhood Repository Maintainer if you need to change something here. - -``` - -``` -#!html -<h1>STM32 avalanche noise entropy source</h1> - -<p>This is an open source and open hardware entropy source, using an -STM32 microcontroller to gather entropy from a common avalanche -noise circuit.</p> - -<p>A special thanks goes to Benedikt Stockebrand who designed the circuit -and the currently used core extraction algorithm in his ARRGH project.</p> - -<p>http://www.stepladder-it.com/Downloads/arrgh-0.2.1alpha.txz</p> - -<h1>Copyrights</h1> - -<p>The license for all work done on this in the CrypTech project is a -3-clause BSD license (see LICENSE.txt for details). Some files have -been generated using the STMicroelectronics initialization code -generator STM32CubeMX and thus have additional copyright header(s).</p> - -<p>The "Noise generator" and "Amplifier" parts of the circuit diagram are -copied from the ARRGH project. ARRGH copyright statement is included -in LICENSE.txt.</p> - -<p>A stripped down copy of the ARM CMSIS library version 3.20 is included -in the Drivers/CMSIS/ directory. Unused parts (and documentation etc.) -have been removed, but every attempt have been made to keep any -licensing information intact. See in particular the file -Drivers/CMSIS/CMSIS END USER LICENCE AGREEMENT.pdf.</p> - -<p>A full copy of the STM32F4xx HAL Drivers is included in the -Drivers/STM32F4xx_HAL_Driver/ directory.</p> - -<h1>Building</h1> - -<p>The following packages need to be installed (on Ubuntu 14.04):</p> - -<p>apt-get install gcc-arm-none-eabi gdb-arm-none-eabi openocd</p> - -<p>XXX not sure this is the complete set, if you find that you need -additional packages please let me know. See e-mail address at the bottom.</p> - -<p>To build the source code, issue "make" from the top level directory -(where this file is). The first time, this will build the complete STM -CMSIS library. A subsequent "make clean" will <em>not</em> clean away the CMSIS -library, but a "make really-clean" will.</p> - -<h1>Installing</h1> - -<p>Do "make flash-target" from the top level directory (where this file is) -to build the firmware for the application selected in the top level -Makefile and flash it into the microcontroller. See the section STLINK -below for information about the actual hardware programming device needed.</p> - -<h1>Using</h1> - -<p>The microcontroller code can currently run in one of two modes, set -statically at the beginning of main(): MODE_DELTAS and MODE_ENTROPY.</p> - -<p>MODE_ENTROPY is the default, and means the microcontroller will send -entropy as binary data as fast as it can get it, which is about 24 kB/s -in the current version of hardware and software. To get some entropy -and perform rudimentary analysis of it, and assuming USB is used and -the device was enumerated as ttyUSB0, do</p> - -<p>ldattach -8 -n -1 -s 460800 tty /dev/ttyUSB0 - echo > /dev/ttyUSB0 - cat /dev/ttyUSB0 | rngtest -c 10 - cat /dev/ttyUSB0 | head -c 100000 | ent</p> - -<p>For Raspberry-Pi, follow any of the guides on the internet for how to -enable the serial port on the GPIO pin header and then try</p> - -<p>ldattach -s 115200 -8 -n -1 tty /dev/ttyAMA0 - echo > /dev/ttyAMA0 - cat /dev/ttyAMA0 | rngtest -c 10 - cat /dev/ttyAMA0 | head -c 100000 | ent</p> - -<p>(the baud rate used with the R-Pi could probably be increased with a -little hardware debugging effort).</p> - -<p>Which UART on the board that will receive the entropy is controlled -by the sending of a newline to the UART ('echo > /dev/ttyUSB0' and -'echo > /dev/ttyAMA0' in the examples above). The power on default is -the USB UART.</p> - -<p>MODE_DELTAS is a quality assurance mode, and outputs the raw Timer IC -values captured for analysis. The stand alone program in src/delta16/ -parses the data format used by MODE_DELTAS and can convert it to -something you can analyse. More about how to do that later.</p> - -<h1>Contents</h1> - -<p>This documentation needs to be improved, but here are some quick notes:</p> - -<p>Hardware design (Eagle and PDF files) are in hardware/rev09/</p> - -<p>The firmware to extract entropy from this hardware is in src/entropy/</p> - -<p>There are additional firmwares to aid in debugging any hardware issues -in src/led-test/ and src/uart-test/</p> - -<h1>Hardware</h1> - -<p>The avalanche noise circuit was first implemented using a NUCLEO-F401RE -evaluation board that has an STM32F401RET6 MCU. Because of human error, -the STM32F401RBT6 was used when assembling rev08 and rev09 boards. This -chip has less flash and RAM, so some region mappings had to change.</p> - -<p>MCU dependant parameters are found in the top level common.mk near the -top, read the comments regarding STDPERIPH_SETTINGS, MCU_LINKSCRIPT and -SRCS.</p> - -<h1>STLINK</h1> - -<p>To program the MCU, an STLINK adapter is used. The cheapest way to get -one is to buy an evaluation board with an STLINK integrated, and pinouts -to program external chips. All the evaluation boards I've encountered -from STM has this ability. I'm using an STLINK from an STM32F4DISCOVERY -board, but the even cheaper NUCLEO-F401RE should work too. The NUCLEO -one has a STLINK v2.1 which is probably, but not necessarily, supported -by the OpenOCD version in your Linux distribution (as of end of 2014).</p> - -<p>The STLINK programming pins are the 1+4 throughole pads above the ARM -on the circuit board. See the schematics for details, but the pinout -from left to right (1, space, 4) of rev09 is</p> - -<p>NRST, space, CLK, IO, GND, VCC</p> - -<h1>Debugging the firmware</h1> - -<p>This site shows several ways to use various debuggers to debug the -firmware in an STM32:</p> - -<p>http://fun-tech.se/stm32/OpenOCD/gdb.php</p> - -<p>I've only managed to get the most basic text line gdb to work, -something along these lines:</p> - -<p>1) Start OpenOCD server (with a configuration file for your type of STLINK - adapter)</p> - -<p>$ openocd -f /usr/share/openocd/scripts/board/stm32f4discovery.cfg</p> - -<p>2) Connect to the OpenOCD server and re-flash already compiled firmware:</p> - -<p>$ telnet localhost 4444 - reset halt - flash probe 0 - stm32f2x mass_erase 0 - flash write_bank 0 /path/to/main.bin 0 - reset halt</p> - -<p>3) Start GDB and have it connect to the OpenOCD server:</p> - -<p>$ arm-none-eabi-gdb --eval-command="target remote localhost:3333" main.elf</p> - -<hr /> - -<p>Fredrik Thulin <a href="mailto:fredrik@thulin.net">fredrik@thulin.net</a>, for the -CrypTech project <a href="https://cryptech.is/">https://cryptech.is/</a> -2015-01-14</p> -``` - -[[RepositoryIndex(format=table,glob=user/ln5/stm32-avalanche-noise)]] - -| Clone `https://git.cryptech.is/user/ln5/stm32-avalanche-noise.git` | -|---| |