aboutsummaryrefslogtreecommitdiff
path: root/README.md
blob: 059b363d1e464df4e2f52a01d27b8dbd881b7989 (plain) (blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161

   

STM32 avalanche noise entropy source

This is an open source and open hardware entropy source, using an STM32 microcontroller to gather entropy from a common avalanche noise circuit.

A special thanks goes to Benedikt Stockebrand who designed the circuit and the currently used core extraction algorithm in his ARRGH project.

http://www.stepladder-it.com/Downloads/arrgh-0.2.1alpha.txz

Copyrights

The license for all work done on this in the CrypTech project is a 3-clause BSD license (see LICENSE.txt for details). Some files have been generated using the STMicroelectronics initialization code generator STM32CubeMX and thus have additional copyright header(s).

The "Noise generator" and "Amplifier" parts of the circuit diagram are copied from the ARRGH project. ARRGH copyright statement is included in LICENSE.txt.

A stripped down copy of the ARM CMSIS library version 3.20 is included in the Drivers/CMSIS/ directory. Unused parts (and documentation etc.) have been removed, but every attempt have been made to keep any licensing information intact. See in particular the file Drivers/CMSIS/CMSIS END USER LICENCE AGREEMENT.pdf.

A full copy of the STM32F4xx HAL Drivers is included in the Drivers/STM32F4xx_HAL_Driver/ directory.

Building

The following packages need to be installed (on Ubuntu 14.04):

apt-get install gcc-arm-none-eabi gdb-arm-none-eabi openocd

XXX not sure this is the complete set, if you find that you need additional packages please let me know. See e-mail address at the bottom.

To build the source code, issue "make" from the top level directory (where this file is). The first time, this will build the complete STM CMSIS library. A subsequent "make clean" will not clean away the CMSIS library, but a "make really-clean" will.

Installing

Do "make flash-target" from the top level directory (where this file is) to build the firmware for the application selected in the top level Makefile and flash it into the microcontroller. See the section STLINK below for information about the actual hardware programming device needed.

Using

The microcontroller code can currently run in one of two modes, set statically at the beginning of main(): MODE_DELTAS and MODE_ENTROPY.

MODE_ENTROPY is the default, and means the microcontroller will send entropy as binary data as fast as it can get it, which is about 24 kB/s in the current version of hardware and software. To get some entropy and perform rudimentary analysis of it, and assuming the device was enumerated as ttyUSB0, do

ldattach -8 -n -1 -s 460800 tty /dev/ttyUSB0 cat /dev/ttyUSB0 | rngtest -c 10 cat /dev/ttyUSB0 | head -c 100000 | ent

MODE_DELTAS is a quality assurance mode, and outputs the raw Timer IC values captured for analysis. The stand alone program in src/delta16/ parses the data format used by MODE_DELTAS and can convert it to something you can analyse. More about how to do that later.

Contents

This documentation needs to be improved, but here are some quick notes:

Hardware design (Eagle and PDF files) are in hardware/rev09/

The firmware to extract entropy from this hardware is in src/entropy/

There are additional firmwares to aid in debugging any hardware issues in src/led-test/ and src/uart-test/

Hardware

The avalanche noise circuit was first implemented using a NUCLEO-F401RE evaluation board that has an STM32F401RET6 MCU. Because of human error, the STM32F401RBT6 was used when assembling rev08 and rev09 boards. This chip has less flash and RAM, so some region mappings had to change.

MCU dependant parameters are found in the top level common.mk near the top, read the comments regarding STDPERIPH_SETTINGS, MCU_LINKSCRIPT and SRCS.

STLINK

To program the MCU, an STLINK adapter is used. The cheapest way to get one is to buy an evaluation board with an STLINK integrated, and pinouts to program external chips. All the evaluation boards I've encountered from STM has this ability. I'm using an STLINK from an STM32F4DISCOVERY board, but the even cheaper NUCLEO-F401RE should work too. The NUCLEO one has a STLINK v2.1 which is probably, but not necessarily, supported by the OpenOCD version in your Linux distribution (as of end of 2014).

The STLINK programming pins are the 1+4 throughole pads above the ARM on the circuit board. See the schematics for details, but the pinout from left to right (1, space, 4) of rev09 is

NRST, space, CLK, IO, GND, VCC

Debugging the firmware

This site shows several ways to use various debuggers to debug the firmware in an STM32:

http://fun-tech.se/stm32/OpenOCD/gdb.php

I've only managed to get the most basic text line gdb to work, something along these lines:

1) Start OpenOCD server (with a configuration file for your type of STLINK adapter)

$ openocd -f /usr/share/openocd/scripts/board/stm32f4discovery.cfg

2) Connect to the OpenOCD server and re-flash already compiled firmware:

$ telnet localhost 4444 reset halt flash probe 0 stm32f2x mass_erase 0 flash write_bank 0 /path/to/main.bin 0 reset halt

3) Start GDB and have it connect to the OpenOCD server:

$ arm-none-eabi-gdb --eval-command="target remote localhost:3333" main.elf


Fredrik Thulin fredrik@thulin.net, for the CrypTech project https://cryptech.is/ 2015-01-14