aboutsummaryrefslogtreecommitdiff
path: root/spiflash_n25q128.c
blob: 728db7ed0b704afd5a29ec7cf9b6449ed2fd31d0 (plain) (blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
/*
 * spiflash_n25q128.c
 * ------------------
 * Functions and defines for accessing SPI flash with part number n25q128.
 *
 * The Alpha board has two of these SPI flash memorys, the FPGA config memory
 * and the keystore memory.
 *
 * Copyright (c) 2016, NORDUnet A/S All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are
 * met:
 * - Redistributions of source code must retain the above copyright notice,
 *   this list of conditions and the following disclaimer.
 *
 * - Redistributions in binary form must reproduce the above copyright
 *   notice, this list of conditions and the following disclaimer in the
 *   documentation and/or other materials provided with the distribution.
 *
 * - Neither the name of the NORDUnet nor the names of its contributors may
 *   be used to endorse or promote products derived from this software
 *   without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
 * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
 * PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
 * HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
 * TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
 * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
 * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */

#include "stm32f4xx_hal.h"
#include "stm-fpgacfg.h"
#include "stm-init.h"

#define _n25q128_select(ctx)	HAL_GPIO_WritePin(ctx->cs_n_port, ctx->cs_n_pin, GPIO_PIN_RESET);
#define _n25q128_deselect(ctx)	HAL_GPIO_WritePin(ctx->cs_n_port, ctx->cs_n_pin, GPIO_PIN_SET);


#define N25Q128_NUM_BYTES	(N25Q128_PAGE_SIZE * N25Q128_NUM_PAGES)

#if N25Q128_SECTOR_SIZE    * N25Q128_NUM_SECTORS    != N25Q128_NUM_BYTES || \
    N25Q128_SUBSECTOR_SIZE * N25Q128_NUM_SUBSECTORS != N25Q128_NUM_BYTES
#error Inconsistant definitions for pages / sectors / subsectors
#endif


int _n25q128_get_wel_flag(struct spiflash_ctx *ctx);


int n25q128_check_id(struct spiflash_ctx *ctx)
{
    // tx, rx buffers
    uint8_t spi_tx[4];
    uint8_t spi_rx[4];

    // result
    HAL_StatusTypeDef ok;

    // send READ ID command
    spi_tx[0] = N25Q128_COMMAND_READ_ID;

    // select, send command & read response, deselect
    _n25q128_select(ctx);
    ok = HAL_SPI_TransmitReceive(ctx->hspi, spi_tx, spi_rx, 4, N25Q128_SPI_TIMEOUT);
    HAL_Delay(1);
    _n25q128_deselect(ctx);

    // check
    if (ok != HAL_OK) return 0;

    // parse response (note, that the very first byte was received during the
    // transfer of the command byte, so it contains garbage and should
    // be ignored here)
    if (spi_rx[1] != N25Q128_ID_MANUFACTURER) return 0;
    if (spi_rx[2] != N25Q128_ID_DEVICE_TYPE) return 0;
    if (spi_rx[3] != N25Q128_ID_DEVICE_CAPACITY) return 0;

    // done
    return 1;
}


int n25q128_read_page(struct spiflash_ctx *ctx, uint32_t page_offset, uint8_t *page_buffer)
{
    // tx buffer
    uint8_t spi_tx[4];

    // result
    HAL_StatusTypeDef ok;

    // check offset
    if (page_offset >= N25Q128_NUM_PAGES) return 0;

    // calculate byte address
    page_offset *= N25Q128_PAGE_SIZE;

    // prepare READ command
    spi_tx[0] = N25Q128_COMMAND_READ_PAGE;
    spi_tx[1] = (uint8_t)(page_offset >> 16);
    spi_tx[2] = (uint8_t)(page_offset >>  8);
    spi_tx[3] = (uint8_t)(page_offset >>  0);

    // activate, send command
    _n25q128_select(ctx);
    ok = HAL_SPI_Transmit(ctx->hspi, spi_tx, 4, N25Q128_SPI_TIMEOUT);
    HAL_Delay(1);

    // check
    if (ok != HAL_OK) {
	_n25q128_deselect(ctx);
	return 0;
    }

    // read response, deselect
    ok = HAL_SPI_Receive(ctx->hspi, page_buffer, N25Q128_PAGE_SIZE, N25Q128_SPI_TIMEOUT);
    HAL_Delay(1);
    _n25q128_deselect(ctx);

    // check
    if (ok != HAL_OK) return 0;

    // done
    return 1;
}


int n25q128_write_page(struct spiflash_ctx *ctx, uint32_t page_offset, const uint8_t *page_buffer)
{
    // tx buffer
    uint8_t spi_tx[4];

    // result
    HAL_StatusTypeDef ok;

    // check offset
    if (page_offset >= N25Q128_NUM_PAGES) return 0;

    // enable writing
    spi_tx[0] = N25Q128_COMMAND_WRITE_ENABLE;

    // activate, send command, deselect
    _n25q128_select(ctx);
    ok = HAL_SPI_Transmit(ctx->hspi, spi_tx, 1, N25Q128_SPI_TIMEOUT);
    HAL_Delay(1);
    _n25q128_deselect(ctx);

    // check
    if (ok != HAL_OK) return 0;

    // make sure, that write enable did the job
    int wel = _n25q128_get_wel_flag(ctx);
    if (wel != 1) return 0;

    // calculate byte address
    page_offset *= N25Q128_PAGE_SIZE;

    // prepare PROGRAM PAGE command
    spi_tx[0] = N25Q128_COMMAND_PAGE_PROGRAM;
    spi_tx[1] = (uint8_t)(page_offset >> 16);
    spi_tx[2] = (uint8_t)(page_offset >>  8);
    spi_tx[3] = (uint8_t)(page_offset >>  0);

    // activate, send command
    _n25q128_select(ctx);
    ok = HAL_SPI_Transmit(ctx->hspi, spi_tx, 4, N25Q128_SPI_TIMEOUT);
    HAL_Delay(1);

    // check
    if (ok != HAL_OK) {
	_n25q128_deselect(ctx);
	return 0;
    }

    // send data, deselect
    ok = HAL_SPI_Transmit(ctx->hspi, (uint8_t *) page_buffer, N25Q128_PAGE_SIZE, N25Q128_SPI_TIMEOUT);
    HAL_Delay(1);
    _n25q128_deselect(ctx);

    // check
    if (ok != HAL_OK) return 0;

    // done
    return 1;
}


int n25q128_get_wip_flag(struct spiflash_ctx *ctx)
{
    // tx, rx buffers
    uint8_t spi_tx[2];
    uint8_t spi_rx[2];

    // result
    HAL_StatusTypeDef ok;

    // send READ STATUS command
    spi_tx[0] = N25Q128_COMMAND_READ_STATUS;

    // send command, read response, deselect
    _n25q128_select(ctx);
    ok = HAL_SPI_TransmitReceive(ctx->hspi, spi_tx, spi_rx, 2, N25Q128_SPI_TIMEOUT);
    HAL_Delay(1);
    _n25q128_deselect(ctx);

    // check
    if (ok != HAL_OK) return -1;

    // done
    return (spi_rx[1] & 1);
}


static int n25q128_erase_something(struct spiflash_ctx *ctx, uint8_t command, uint32_t byte_offset)
{
    // check offset
    if (byte_offset >= N25Q128_NUM_BYTES) return 0;

    // tx buffer
    uint8_t spi_tx[4];

    // result
    HAL_StatusTypeDef ok;

    // enable writing
    spi_tx[0] = N25Q128_COMMAND_WRITE_ENABLE;

    // select, send command, deselect
    _n25q128_select(ctx);
    ok = HAL_SPI_Transmit(ctx->hspi, spi_tx, 1, N25Q128_SPI_TIMEOUT);
    HAL_Delay(1);
    _n25q128_deselect(ctx);

    // check
    if (ok != HAL_OK) return 0;

    // make sure, that write enable did the job
    int wel = _n25q128_get_wel_flag(ctx);
    if (wel != 1) return 0;

    // send command (ERASE SECTOR or ERASE SUBSECTOR)
    spi_tx[0] = command;
    spi_tx[1] = (uint8_t)(byte_offset >> 16);
    spi_tx[2] = (uint8_t)(byte_offset >>  8);
    spi_tx[3] = (uint8_t)(byte_offset >>  0);

    // activate, send command, deselect
    _n25q128_select(ctx);
    ok = HAL_SPI_Transmit(ctx->hspi, spi_tx, 4, N25Q128_SPI_TIMEOUT);
    HAL_Delay(1);
    _n25q128_deselect(ctx);

    // check
    if (ok != HAL_OK) return 0;

    // done
    return 1;
}


int n25q128_erase_sector(struct spiflash_ctx *ctx, uint32_t sector_offset)
{
    return n25q128_erase_something(ctx, N25Q128_COMMAND_ERASE_SECTOR,
				   sector_offset * N25Q128_SECTOR_SIZE);
}


int n25q128_erase_subsector(struct spiflash_ctx *ctx, uint32_t subsector_offset)
{
    return n25q128_erase_something(ctx, N25Q128_COMMAND_ERASE_SUBSECTOR,
				   subsector_offset * N25Q128_SUBSECTOR_SIZE);
}


int _n25q128_get_wel_flag(struct spiflash_ctx *ctx)
{
    // tx, rx buffers
    uint8_t spi_tx[2];
    uint8_t spi_rx[2];

    // result
    HAL_StatusTypeDef ok;

    // send READ STATUS command
    spi_tx[0] = N25Q128_COMMAND_READ_STATUS;

    // send command, read response, deselect
    _n25q128_select(ctx);
    ok = HAL_SPI_TransmitReceive(ctx->hspi, spi_tx, spi_rx, 2, N25Q128_SPI_TIMEOUT);
    HAL_Delay(1);
    _n25q128_deselect(ctx);

    // check
    if (ok != HAL_OK) return -1;

    // done
    return ((spi_rx[1] >> 1) & 1);
}

/* Wait until the flash memory is done writing (wip = Write In Progress) */
inline int _wait_while_wip(struct spiflash_ctx *ctx, uint32_t timeout)
{
    int i;
    while (timeout--) {
	i = n25q128_get_wip_flag(ctx);
	if (i < 0) return 0;
	if (! i) break;
	HAL_Delay(10);
    }
    return 1;
}

/* This function performs erasure if needed, and then writing of a number of pages to the flash memory */
int n25q128_write_data(struct spiflash_ctx *ctx, uint32_t offset, const uint8_t *buf, const uint32_t len, const int auto_erase)
{
    uint32_t page;

    /* Ensure alignment */
    if ((offset % N25Q128_PAGE_SIZE) != 0) return -1;
    if ((len % N25Q128_PAGE_SIZE) != 0) return -2;

    if (auto_erase && (offset % N25Q128_SECTOR_SIZE) == 0) {
	/*
	 * first page in sector, need to erase sector
	 *
	 * So why do we only do this when the buffer starts on the
	 * sector, as opposed to performing this check for every page?
	 * Also, might be better to do this by subsectors rather than
	 * sectors.
	 */

	if (! _wait_while_wip(ctx, 1000)) return -3;

	if (! n25q128_erase_sector(ctx, offset / N25Q128_SECTOR_SIZE)) {
	    return -4;
	}
    }

    for (page = 0; page < len / N25Q128_PAGE_SIZE; page++) {
	if (! _wait_while_wip(ctx, 1000)) return -5;

	if (! n25q128_write_page(ctx, offset / N25Q128_PAGE_SIZE, buf)) {
	    return -6;
	}
	buf += N25Q128_PAGE_SIZE;
	offset += N25Q128_PAGE_SIZE;

	/* XXX read back data and verify it, or maybe just verify ability to write
	 * to memory by verifying the contents of one page after erase?
	 */
    }

    return 1;
}

/* This function reads zero or more pages from the SPI flash. */
int n25q128_read_data(struct spiflash_ctx *ctx, uint32_t offset, uint8_t *buf, const uint32_t len)
{
    uint32_t page;

    /* Ensure alignment */
    if ((offset % N25Q128_PAGE_SIZE) != 0) return -1;
    if ((len % N25Q128_PAGE_SIZE) != 0) return -2;

    for (page = 0; page < len / N25Q128_PAGE_SIZE; page++) {
	if (! n25q128_read_page(ctx, offset / N25Q128_PAGE_SIZE, buf)) {
	    return -3;
	}
	buf += N25Q128_PAGE_SIZE;
	offset += N25Q128_PAGE_SIZE;
    }

    return 1;
}