aboutsummaryrefslogtreecommitdiff
path: root/projects/bootloader/bootloader.c
blob: c0f981fc3f0fe627415e67a35a1a29a723d20745 (plain) (blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
/*
 * bootloader.c
 * ------------
 * Bootloader to either install new firmware received from the MGMT UART,
 * or jump to previously installed firmware.
 *
 * Copyright (c) 2016, NORDUnet A/S All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are
 * met:
 * - Redistributions of source code must retain the above copyright notice,
 *   this list of conditions and the following disclaimer.
 *
 * - Redistributions in binary form must reproduce the above copyright
 *   notice, this list of conditions and the following disclaimer in the
 *   documentation and/or other materials provided with the distribution.
 *
 * - Neither the name of the NORDUnet nor the names of its contributors may
 *   be used to endorse or promote products derived from this software
 *   without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
 * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
 * PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
 * HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
 * TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
 * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
 * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */
#include "stm-init.h"
#include "stm-led.h"
#include "stm-uart.h"
#include "stm-fmc.h"
#include "dfu.h"

/* stub these out to avoid linker error */
void fpgacfg_init(void) { }
void sdram_init(void) { }

/* Linker symbols are strange in C. Make regular pointers for sanity. */
__IO uint32_t *dfu_control = &CRYPTECH_DFU_CONTROL;
__IO uint32_t *dfu_firmware = &CRYPTECH_FIRMWARE_START;
/* The first word in the firmware is an address to the stack (msp) */
__IO uint32_t *dfu_msp_ptr = &CRYPTECH_FIRMWARE_START;
/* The second word in the firmware is a pointer to the code
 * (points at the Reset_Handler from the linker script).
 */
__IO uint32_t *dfu_code_ptr = &CRYPTECH_FIRMWARE_START + 1;

typedef  void (*pFunction)(void);

/* called from Reset_Handler */
void check_early_dfu_jump(void)
{
    /* Check if we've just rebooted in order to jump to the firmware. */
    if (*dfu_control == HARDWARE_EARLY_DFU_JUMP) {
	*dfu_control = 0;
        pFunction loaded_app = (pFunction) *dfu_code_ptr;
        /* Set the stack pointer to the correct one for the firmware */
        __set_MSP(*dfu_msp_ptr);
        /* Set the Vector Table Offset Register */
        SCB->VTOR = (uint32_t) dfu_firmware;
        loaded_app();
        while (1);
    }
}

int should_dfu()
{
    int i;
    uint8_t rx = 0;

    /* While blinking the blue LED for 5 seconds, see if we receive a CR on the MGMT UART.
     * We've discussed also requiring one or both of the FPGA config jumpers installed
     * before allowing DFU of the STM32 - that check could be done here.
     */
    led_on(LED_BLUE);
    for (i = 0; i < 50; i++) {
	HAL_Delay(100);
	led_toggle(LED_BLUE);
	if (uart_recv_char2(STM_UART_MGMT, &rx, 0) == HAL_OK) {
	    if (rx == 13) return 1;
	}
    }
    return 0;
}

/* Sleep for specified number of seconds -- used after bad PIN. */
void hal_sleep(const unsigned seconds) { HAL_Delay(seconds * 1000); }

int main(void)
{
    int status;

    stm_init();

    uart_send_string2(STM_UART_MGMT, (char *) "\r\n\r\nThis is the bootloader speaking...");

    if (should_dfu()) {
	led_off(LED_BLUE);
	if ((status = dfu_receive_firmware()) != 0) {
	    /* Upload of new firmware failed, reboot after lighting the red LED
	     * for three seconds.
	     */
	    led_off(LED_BLUE);
	    led_on(LED_RED);
	    uart_send_string2(STM_UART_MGMT, (char *) "dfu_receive_firmware failed: ");
	    uart_send_number2(STM_UART_MGMT, status, 3, 16);
	    uart_send_string2(STM_UART_MGMT, (char *) "\r\n\r\nRebooting in three seconds\r\n");
	    HAL_Delay(3000);
	    HAL_NVIC_SystemReset();
	    while (1) {};
	}
    }

    /* Set dfu_control to the magic value that will cause the us to call do_early_dfu_jump
     * after rebooting back into this main() function.
     */
    *dfu_control = HARDWARE_EARLY_DFU_JUMP;

    uart_send_string2(STM_UART_MGMT, (char *) "loading firmware\r\n\r\n");

    /* De-initialize hardware by rebooting */
    HAL_NVIC_SystemReset();
    while (1) {};
}