diff options
Diffstat (limited to 'stm32f4xx_hal_conf.h')
| -rw-r--r-- | stm32f4xx_hal_conf.h | 423 |
1 files changed, 0 insertions, 423 deletions
diff --git a/stm32f4xx_hal_conf.h b/stm32f4xx_hal_conf.h deleted file mode 100644 index fd13d9e..0000000 --- a/stm32f4xx_hal_conf.h +++ /dev/null @@ -1,423 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f4xx_hal_conf.h - * @brief HAL configuration file. - ****************************************************************************** - * @attention - * - * <h2><center>© COPYRIGHT(c) 2015 STMicroelectronics</center></h2> - * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F4xx_HAL_CONF_H -#define __STM32F4xx_HAL_CONF_H - -#ifdef __cplusplus - extern "C" { -#endif - -/* Exported types ------------------------------------------------------------*/ -/* Exported constants --------------------------------------------------------*/ - -/* ########################## Module Selection ############################## */ -/** - * @brief This is the list of modules to be used in the HAL driver - */ -#define HAL_MODULE_ENABLED - -//#define HAL_ADC_MODULE_ENABLED -//#define HAL_CAN_MODULE_ENABLED -//#define HAL_CRC_MODULE_ENABLED -//#define HAL_CRYP_MODULE_ENABLED -//#define HAL_DAC_MODULE_ENABLED -//#define HAL_DCMI_MODULE_ENABLED -//#define HAL_DMA2D_MODULE_ENABLED -//#define HAL_ETH_MODULE_ENABLED -//#define HAL_NAND_MODULE_ENABLED -//#define HAL_NOR_MODULE_ENABLED -//#define HAL_PCCARD_MODULE_ENABLED -#define HAL_SRAM_MODULE_ENABLED -//#define HAL_SDRAM_MODULE_ENABLED -//#define HAL_HASH_MODULE_ENABLED -//#define HAL_I2C_MODULE_ENABLED -//#define HAL_I2S_MODULE_ENABLED -//#define HAL_IWDG_MODULE_ENABLED -//#define HAL_LTDC_MODULE_ENABLED -#define HAL_RNG_MODULE_ENABLED -//#define HAL_RTC_MODULE_ENABLED -//#define HAL_SAI_MODULE_ENABLED -//#define HAL_SD_MODULE_ENABLED -//#define HAL_SPI_MODULE_ENABLED -//#define HAL_TIM_MODULE_ENABLED -#define HAL_UART_MODULE_ENABLED -//#define HAL_USART_MODULE_ENABLED -//#define HAL_IRDA_MODULE_ENABLED -//#define HAL_SMARTCARD_MODULE_ENABLED -//#define HAL_WWDG_MODULE_ENABLED -//#define HAL_PCD_MODULE_ENABLED -//#define HAL_HCD_MODULE_ENABLED -//#define HAL_QSPI_MODULE_ENABLED -//#define HAL_QSPI_MODULE_ENABLED -//#define HAL_CEC_MODULE_ENABLED -//#define HAL_FMPI2C_MODULE_ENABLED -//#define HAL_SPDIFRX_MODULE_ENABLED -#define HAL_GPIO_MODULE_ENABLED -#define HAL_DMA_MODULE_ENABLED -#define HAL_RCC_MODULE_ENABLED -#define HAL_FLASH_MODULE_ENABLED -#define HAL_PWR_MODULE_ENABLED -#define HAL_CORTEX_MODULE_ENABLED - -/* ########################## HSE/HSI Values adaptation ##################### */ -/** - * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. - * This value is used by the RCC HAL module to compute the system frequency - * (when HSE is used as system clock source, directly or through the PLL). - */ -#if !defined (HSE_VALUE) - #define HSE_VALUE ((uint32_t)25000000) /*!< Value of the External oscillator in Hz */ -#endif /* HSE_VALUE */ - -#if !defined (HSE_STARTUP_TIMEOUT) - #define HSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSE start up, in ms */ -#endif /* HSE_STARTUP_TIMEOUT */ - -/** - * @brief Internal High Speed oscillator (HSI) value. - * This value is used by the RCC HAL module to compute the system frequency - * (when HSI is used as system clock source, directly or through the PLL). - */ -#if !defined (HSI_VALUE) - #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/ -#endif /* HSI_VALUE */ - -/** - * @brief Internal Low Speed oscillator (LSI) value. - */ -#if !defined (LSI_VALUE) - #define LSI_VALUE ((uint32_t)32000) -#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz - The real value may vary depending on the variations - in voltage and temperature. */ -/** - * @brief External Low Speed oscillator (LSE) value. - */ -#if !defined (LSE_VALUE) - #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External Low Speed oscillator in Hz */ -#endif /* LSE_VALUE */ - -/** - * @brief External clock source for I2S peripheral - * This value is used by the I2S HAL module to compute the I2S clock source - * frequency, this source is inserted directly through I2S_CKIN pad. - */ -#if !defined (EXTERNAL_CLOCK_VALUE) - #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000) /*!< Value of the External audio frequency in Hz*/ -#endif /* EXTERNAL_CLOCK_VALUE */ - -/* Tip: To avoid modifying this file each time you need to use different HSE, - === you can define the HSE value in your toolchain compiler preprocessor. */ - -/* ########################### System Configuration ######################### */ -/** - * @brief This is the HAL system configuration section - */ - -#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */ -#define TICK_INT_PRIORITY ((uint32_t)0) /*!< tick interrupt priority */ -#define USE_RTOS 0 -#define PREFETCH_ENABLE 1 -#define INSTRUCTION_CACHE_ENABLE 1 -#define DATA_CACHE_ENABLE 1 - -/* ########################## Assert Selection ############################## */ -/** - * @brief Uncomment the line below to expanse the "assert_param" macro in the - * HAL drivers code - */ -/* #define USE_FULL_ASSERT 1 */ - -/* ################## Ethernet peripheral configuration ##################### */ - -/* Section 1 : Ethernet peripheral configuration */ - -/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ -#define MAC_ADDR0 2 -#define MAC_ADDR1 0 -#define MAC_ADDR2 0 -#define MAC_ADDR3 0 -#define MAC_ADDR4 0 -#define MAC_ADDR5 0 - -/* Definition of the Ethernet driver buffers size and count */ -#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ -#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ -#define ETH_RXBUFNB ((uint32_t)4) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ -#define ETH_TXBUFNB ((uint32_t)4) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ - -/* Section 2: PHY configuration section */ - -/* DP83848 PHY Address*/ -#define DP83848_PHY_ADDRESS 0x01 -/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ -#define PHY_RESET_DELAY ((uint32_t)0x000000FF) -/* PHY Configuration delay */ -#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF) - -#define PHY_READ_TO ((uint32_t)0x0000FFFF) -#define PHY_WRITE_TO ((uint32_t)0x0000FFFF) - -/* Section 3: Common PHY Registers */ - -#define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */ -#define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */ - -#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ -#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ -#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ -#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ -#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ -#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ -#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ -#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ -#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ -#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ - -#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ -#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ -#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ - -/* Section 4: Extended PHY Registers */ - -#define PHY_SR ((uint16_t)0x10) /*!< PHY status register Offset */ -#define PHY_MICR ((uint16_t)0x11) /*!< MII Interrupt Control Register */ -#define PHY_MISR ((uint16_t)0x12) /*!< MII Interrupt Status and Misc. Control Register */ - -#define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */ -#define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */ -#define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */ - -#define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */ -#define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */ - -#define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */ -#define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */ - -/* Includes ------------------------------------------------------------------*/ -/** - * @brief Include module's header file - */ - -#ifdef HAL_RCC_MODULE_ENABLED - #include "stm32f4xx_hal_rcc.h" -#endif /* HAL_RCC_MODULE_ENABLED */ - -#ifdef HAL_GPIO_MODULE_ENABLED - #include "stm32f4xx_hal_gpio.h" -#endif /* HAL_GPIO_MODULE_ENABLED */ - -#ifdef HAL_DMA_MODULE_ENABLED - #include "stm32f4xx_hal_dma.h" -#endif /* HAL_DMA_MODULE_ENABLED */ - -#ifdef HAL_CORTEX_MODULE_ENABLED - #include "stm32f4xx_hal_cortex.h" -#endif /* HAL_CORTEX_MODULE_ENABLED */ - -#ifdef HAL_ADC_MODULE_ENABLED - #include "stm32f4xx_hal_adc.h" -#endif /* HAL_ADC_MODULE_ENABLED */ - -#ifdef HAL_CAN_MODULE_ENABLED - #include "stm32f4xx_hal_can.h" -#endif /* HAL_CAN_MODULE_ENABLED */ - -#ifdef HAL_CRC_MODULE_ENABLED - #include "stm32f4xx_hal_crc.h" -#endif /* HAL_CRC_MODULE_ENABLED */ - -#ifdef HAL_CRYP_MODULE_ENABLED - #include "stm32f4xx_hal_cryp.h" -#endif /* HAL_CRYP_MODULE_ENABLED */ - -#ifdef HAL_DMA2D_MODULE_ENABLED - #include "stm32f4xx_hal_dma2d.h" -#endif /* HAL_DMA2D_MODULE_ENABLED */ - -#ifdef HAL_DAC_MODULE_ENABLED - #include "stm32f4xx_hal_dac.h" -#endif /* HAL_DAC_MODULE_ENABLED */ - -#ifdef HAL_DCMI_MODULE_ENABLED - #include "stm32f4xx_hal_dcmi.h" -#endif /* HAL_DCMI_MODULE_ENABLED */ - -#ifdef HAL_ETH_MODULE_ENABLED - #include "stm32f4xx_hal_eth.h" -#endif /* HAL_ETH_MODULE_ENABLED */ - -#ifdef HAL_FLASH_MODULE_ENABLED - #include "stm32f4xx_hal_flash.h" -#endif /* HAL_FLASH_MODULE_ENABLED */ - -#ifdef HAL_SRAM_MODULE_ENABLED - #include "stm32f4xx_hal_sram.h" -#endif /* HAL_SRAM_MODULE_ENABLED */ - -#ifdef HAL_NOR_MODULE_ENABLED - #include "stm32f4xx_hal_nor.h" -#endif /* HAL_NOR_MODULE_ENABLED */ - -#ifdef HAL_NAND_MODULE_ENABLED - #include "stm32f4xx_hal_nand.h" -#endif /* HAL_NAND_MODULE_ENABLED */ - -#ifdef HAL_PCCARD_MODULE_ENABLED - #include "stm32f4xx_hal_pccard.h" -#endif /* HAL_PCCARD_MODULE_ENABLED */ - -#ifdef HAL_SDRAM_MODULE_ENABLED - #include "stm32f4xx_hal_sdram.h" -#endif /* HAL_SDRAM_MODULE_ENABLED */ - -#ifdef HAL_HASH_MODULE_ENABLED - #include "stm32f4xx_hal_hash.h" -#endif /* HAL_HASH_MODULE_ENABLED */ - -#ifdef HAL_I2C_MODULE_ENABLED - #include "stm32f4xx_hal_i2c.h" -#endif /* HAL_I2C_MODULE_ENABLED */ - -#ifdef HAL_I2S_MODULE_ENABLED - #include "stm32f4xx_hal_i2s.h" -#endif /* HAL_I2S_MODULE_ENABLED */ - -#ifdef HAL_IWDG_MODULE_ENABLED - #include "stm32f4xx_hal_iwdg.h" -#endif /* HAL_IWDG_MODULE_ENABLED */ - -#ifdef HAL_LTDC_MODULE_ENABLED - #include "stm32f4xx_hal_ltdc.h" -#endif /* HAL_LTDC_MODULE_ENABLED */ - -#ifdef HAL_PWR_MODULE_ENABLED - #include "stm32f4xx_hal_pwr.h" -#endif /* HAL_PWR_MODULE_ENABLED */ - -#ifdef HAL_RNG_MODULE_ENABLED - #include "stm32f4xx_hal_rng.h" -#endif /* HAL_RNG_MODULE_ENABLED */ - -#ifdef HAL_RTC_MODULE_ENABLED - #include "stm32f4xx_hal_rtc.h" -#endif /* HAL_RTC_MODULE_ENABLED */ - -#ifdef HAL_SAI_MODULE_ENABLED - #include "stm32f4xx_hal_sai.h" -#endif /* HAL_SAI_MODULE_ENABLED */ - -#ifdef HAL_SD_MODULE_ENABLED - #include "stm32f4xx_hal_sd.h" -#endif /* HAL_SD_MODULE_ENABLED */ - -#ifdef HAL_SPI_MODULE_ENABLED - #include "stm32f4xx_hal_spi.h" -#endif /* HAL_SPI_MODULE_ENABLED */ - -#ifdef HAL_TIM_MODULE_ENABLED - #include "stm32f4xx_hal_tim.h" -#endif /* HAL_TIM_MODULE_ENABLED */ - -#ifdef HAL_UART_MODULE_ENABLED - #include "stm32f4xx_hal_uart.h" -#endif /* HAL_UART_MODULE_ENABLED */ - -#ifdef HAL_USART_MODULE_ENABLED - #include "stm32f4xx_hal_usart.h" -#endif /* HAL_USART_MODULE_ENABLED */ - -#ifdef HAL_IRDA_MODULE_ENABLED - #include "stm32f4xx_hal_irda.h" -#endif /* HAL_IRDA_MODULE_ENABLED */ - -#ifdef HAL_SMARTCARD_MODULE_ENABLED - #include "stm32f4xx_hal_smartcard.h" -#endif /* HAL_SMARTCARD_MODULE_ENABLED */ - -#ifdef HAL_WWDG_MODULE_ENABLED - #include "stm32f4xx_hal_wwdg.h" -#endif /* HAL_WWDG_MODULE_ENABLED */ - -#ifdef HAL_PCD_MODULE_ENABLED - #include "stm32f4xx_hal_pcd.h" -#endif /* HAL_PCD_MODULE_ENABLED */ - -#ifdef HAL_HCD_MODULE_ENABLED - #include "stm32f4xx_hal_hcd.h" -#endif /* HAL_HCD_MODULE_ENABLED */ - -#ifdef HAL_QSPI_MODULE_ENABLED - #include "stm32f4xx_hal_qspi.h" -#endif /* HAL_QSPI_MODULE_ENABLED */ - -#ifdef HAL_CEC_MODULE_ENABLED - #include "stm32f4xx_hal_cec.h" -#endif /* HAL_CEC_MODULE_ENABLED */ - -#ifdef HAL_FMPI2C_MODULE_ENABLED - #include "stm32f4xx_hal_fmpi2c.h" -#endif /* HAL_FMPI2C_MODULE_ENABLED */ - -#ifdef HAL_SPDIFRX_MODULE_ENABLED - #include "stm32f4xx_hal_spdifrx.h" -#endif /* HAL_SPDIFRX_MODULE_ENABLED */ - -/* Exported macro ------------------------------------------------------------*/ -#ifdef USE_FULL_ASSERT -/** - * @brief The assert_param macro is used for function's parameters check. - * @param expr: If expr is false, it calls assert_failed function - * which reports the name of the source file and the source - * line number of the call that failed. - * If expr is true, it returns no value. - * @retval None - */ - #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) -/* Exported functions ------------------------------------------------------- */ - void assert_failed(uint8_t* file, uint32_t line); -#else - #define assert_param(expr) ((void)0) -#endif /* USE_FULL_ASSERT */ - -#ifdef __cplusplus -} -#endif - -#endif /* __STM32F4xx_HAL_CONF_H */ - - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |