diff options
Diffstat (limited to 'core_selector/src/rtl/hash_selector.v')
-rw-r--r-- | core_selector/src/rtl/hash_selector.v | 260 |
1 files changed, 0 insertions, 260 deletions
diff --git a/core_selector/src/rtl/hash_selector.v b/core_selector/src/rtl/hash_selector.v deleted file mode 100644 index 81fac7d..0000000 --- a/core_selector/src/rtl/hash_selector.v +++ /dev/null @@ -1,260 +0,0 @@ -//====================================================================== -// -// hash_selector.v -// --------------- -// Top level wrapper that creates the Cryptech coretest system. -// The wrapper contains instances of external interface, coretest -// and the core to be tested. And if more than one core is -// present the wrapper also includes address and data muxes. -// -// -// Authors: Joachim Strombergson, Paul Selkirk, Pavel Shatov -// Copyright (c) 2014-2015, NORDUnet A/S All rights reserved. -// -// Redistribution and use in source and binary forms, with or without -// modification, are permitted provided that the following conditions are -// met: -// - Redistributions of source code must retain the above copyright notice, -// this list of conditions and the following disclaimer. -// -// - Redistributions in binary form must reproduce the above copyright -// notice, this list of conditions and the following disclaimer in the -// documentation and/or other materials provided with the distribution. -// -// - Neither the name of the NORDUnet nor the names of its contributors may -// be used to endorse or promote products derived from this software -// without specific prior written permission. -// -// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS -// IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED -// TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A -// PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT -// HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, -// SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED -// TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR -// PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF -// LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING -// NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS -// SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. -// -//====================================================================== - -module hash_selector - ( - input wire sys_clk, - input wire sys_rst_n, - input wire sys_ena, - - input wire [13 : 0] sys_eim_addr, - input wire sys_eim_wr, - input wire sys_eim_rd, - output wire [31 : 0] sys_read_data, - input wire [31 : 0] sys_write_data, - output wire sys_error - ); - - /* In this memory segment (HASHES) we have 14 address bits. Every core has - * 8-bit internal address space, so we can have up to 2^(14-8) = 64 cores here. - * - * So far we have three cores: SHA-1, SHA-256 and SHA-512. - */ - - /********************************************************* - * To add new HASH core named XXX follow the steps below * - ********************************************************* - * - * 1. Add corresponding `define under "List of Available Cores", this will - * allow users to exclude your core from implementation to save some - * slices in case they don't need it. - * - * `define USE_CORE_XXX -XXX define in wrapper core - * - * - * 2. Choose address of your new core and add corresponding line under - * "Core Address Table". Core addresses can be in the range from 0 to 63 - * inclusively. - * - * localparam CORE_ADDR_XXX = 6'dN; -XXX move to `define in wrapper core?? - * - * - * 3. Add instantiation of your new core after all existing cores - * surrounded by conditional synthesis directives. - * You also need a 32-bit output (read data) bus for your core and an - * enable flag. Note that sys_rst_n in an active-low sync reset signal. - * - * `ifdef USE_CORE_XXX - * wire [31: 0] read_data_xxx; - * wire enable_xxx = sys_ena && (addr_core_num == CORE_ADDR_XXX); - * xxx xxx_inst - * ( - * .clk(sys_clk), - * .reset_n(sys_rst_n), - * .cs(enable_xxx & (sys_eim_rd | sys_eim_wr)), - * .we(sys_eim_wr), - * .address(addr_core_reg), - * .write_data(sys_write_data), - * .read_data(read_data_xxx), - * .error() - * ); - * `endif - * - * - * 4. Add previously created data bus to "Output (Read Data) Multiplexor" - * in the end of this file. - * - * `ifdef USE_CORE_XXX - * CORE_ADDR_XXX: - * sys_read_data_mux = read_data_xxx; - * `endif - * - */ - - - //---------------------------------------------------------------- - // Address Decoder - //---------------------------------------------------------------- - // upper 6 bits specify core being addressed - wire [ 5: 0] addr_core_num = sys_eim_addr[13: 8]; - // lower 8 bits specify register offset in core - wire [ 7: 0] addr_core_reg = sys_eim_addr[ 7: 0]; - - - //---------------------------------------------------------------- - // List of Available Cores - //---------------------------------------------------------------- - // Comment following lines to exclude cores from implementation. - `define USE_CORE_SHA1 - `define USE_CORE_SHA256 - `define USE_CORE_SHA512 - - - //---------------------------------------------------------------- - // Core Address Table - //---------------------------------------------------------------- - localparam CORE_ADDR_SHA1 = 6'd0; - localparam CORE_ADDR_SHA256 = 6'd1; - localparam CORE_ADDR_SHA512 = 6'd2; - - - //---------------------------------------------------------------- - // SHA-1 - //---------------------------------------------------------------- - `ifdef USE_CORE_SHA1 - wire enable_sha1 = sys_ena && (addr_core_num == CORE_ADDR_SHA1); - wire [31: 0] read_data_sha1; - wire error_sha1; - - sha1 sha1_inst - ( - .clk(sys_clk), - .reset_n(sys_rst_n), - - .cs(enable_sha1 & (sys_eim_rd | sys_eim_wr)), - .we(sys_eim_wr), - - .address(addr_core_reg), - .write_data(sys_write_data), - .read_data(read_data_sha1), - .error(error_sha1) - ); - `endif - - - //---------------------------------------------------------------- - // SHA-256 - //---------------------------------------------------------------- - `ifdef USE_CORE_SHA256 - wire enable_sha256 = sys_ena && (addr_core_num == CORE_ADDR_SHA256); - wire [31: 0] read_data_sha256; - wire error_sha256; - - sha256 sha256_inst - ( - .clk(sys_clk), - .reset_n(sys_rst_n), - - .cs(enable_sha256 & (sys_eim_rd | sys_eim_wr)), - .we(sys_eim_wr), - - .address(addr_core_reg), - .write_data(sys_write_data), - .read_data(read_data_sha256), - .error(error_sha256) - ); - `endif - - - //---------------------------------------------------------------- - // SHA-512 - //---------------------------------------------------------------- - `ifdef USE_CORE_SHA512 - wire enable_sha512 = sys_ena && (addr_core_num == CORE_ADDR_SHA512); - wire [31: 0] read_data_sha512; - wire error_sha512; - - sha512 sha512_inst - ( - .clk(sys_clk), - .reset_n(sys_rst_n), - - .cs(enable_sha512 & (sys_eim_rd | sys_eim_wr)), - .we(sys_eim_wr), - - .address(addr_core_reg), - .write_data(sys_write_data), - .read_data(read_data_sha512), - .error(error_sha512) - ); - `endif - - - //---------------------------------------------------------------- - // Output (Read Data) Multiplexor - //---------------------------------------------------------------- - reg [31: 0] sys_read_data_mux; - assign sys_read_data = sys_read_data_mux; - reg sys_error_mux; - assign sys_error = sys_error_mux; - - always @* - // - case (addr_core_num) - // - `ifdef USE_CORE_SHA1 - CORE_ADDR_SHA1: - begin - sys_read_data_mux = read_data_sha1; - sys_error_mux = error_sha1; - end - `endif - `ifdef USE_CORE_SHA256 - CORE_ADDR_SHA256: - begin - sys_read_data_mux = read_data_sha256; - sys_error_mux = error_sha256; - end - `endif - `ifdef USE_CORE_SHA512 - CORE_ADDR_SHA512: - begin - sys_read_data_mux = read_data_sha512; - sys_error_mux = error_sha512; - end - `endif - // - default: - begin - sys_read_data_mux = {32{1'b0}}; - sys_error_mux = 1; - end - // - endcase - - -endmodule - -//====================================================================== -// EOF hash_selector.v -//====================================================================== |