init

8 files changed, 947 insertions, 0 deletions

diff --git a/src/uart-test/Makefile b/src/uart-test/Makefile
new file mode 100644
index 0000000..dc4834c
--- /dev/null
+++ b/src/uart-test/Makefile
@@ -0,0 +1,50 @@
+# put your *.o targets here, make should handle the rest!
+SRCS = main.c stm_init.c system_stm32f4xx.c stm32f4xx_it.c stm32f4xx_hal_msp.c
+
+# all the files will be generated with this name
+PROJ_NAME=uart-test
+
+TOPLEVEL=../..
+include $(TOPLEVEL)/common.mk
+
+OBJS = $(SRCS:.c=.o)
+
+###################################################
+
+.PHONY: lib proj
+
+all: lib proj
+
+lib:
+	$(MAKE) -C $(STD_PERIPH_LIB) STDPERIPH_SETTINGS="$(STDPERIPH_SETTINGS)"
+
+
+proj: 	$(PROJ_NAME).elf
+
+$(PROJ_NAME).elf: $(SRCS)
+	$(CC) $(CFLAGS) $^ -o $@ -L$(STD_PERIPH_LIB) -lstmf4 -L$(LDSCRIPT_INC) -T$(MCU_LINKSCRIPT) -g
+	$(OBJCOPY) -O ihex $(PROJ_NAME).elf $(PROJ_NAME).hex
+	$(OBJCOPY) -O binary $(PROJ_NAME).elf $(PROJ_NAME).bin
+	$(OBJDUMP) -St $(PROJ_NAME).elf >$(PROJ_NAME).lst
+	$(SIZE) $(PROJ_NAME).elf
+
+clean:
+	find ./ -name '*~' | xargs rm -f
+	rm -f *.o
+	rm -f $(PROJ_NAME).elf
+	rm -f $(PROJ_NAME).hex
+	rm -f $(PROJ_NAME).bin
+	rm -f $(PROJ_NAME).map
+	rm -f $(PROJ_NAME).lst
+
+really-clean: clean
+	$(MAKE) -C $(STD_PERIPH_LIB) clean
+
+debug:
+    $(GDB) -ex "target remote localhost:3333" \
+        -ex "set remote hardware-breakpoint-limit 6" \
+        -ex "set remote hardware-watchpoint-limit 4" $(PROJ_NAME).elf
+
+flash-target:
+	$(OPENOCD) -f $(OPENOCD_BOARD_DIR)/$(OPENOCD_PROC_FILE) \
+		-c "program $(PROJ_NAME).elf verify reset"
diff --git a/src/uart-test/main.c b/src/uart-test/main.c
new file mode 100644
index 0000000..77c17f4
--- /dev/null
+++ b/src/uart-test/main.c
@@ -0,0 +1,32 @@
+/*
+ * Test code that just sends the letters 'a' to 'z' over and
+ * over again using USART1.
+ *
+ * Toggles the BLUE LED slowly and the YELLOW LED for every
+ * character sent.
+ */
+#include "stm_init.h"
+
+#define DELAY() HAL_Delay(250)
+
+int
+main()
+{
+  uint8_t c = 'a';
+  uint32_t i = 0;
+
+  stm_init();
+
+  while (1)
+  {
+    HAL_GPIO_TogglePin(LED_PORT, LED_YELLOW);
+
+    HAL_UART_Transmit(&huart1, (uint8_t *) &c, 1, 0xff);
+    DELAY();
+
+    if (c++ == 'z') {
+      c = 'a';
+      HAL_GPIO_TogglePin(LED_PORT, LED_BLUE);
+    }
+  }
+}
diff --git a/src/uart-test/stm32f4xx_hal_msp.c b/src/uart-test/stm32f4xx_hal_msp.c
new file mode 100644
index 0000000..2b1da7e
--- /dev/null
+++ b/src/uart-test/stm32f4xx_hal_msp.c
@@ -0,0 +1,42 @@
+/*

+ * Init/de-init USART1.

+ *

+ * Pins used:

+ *

+ *   PA9:  USART1_TX

+ *   PA10: USART1_RX

+ */

+

+#include "stm32f4xx_hal.h"

+

+

+void HAL_UART_MspInit(UART_HandleTypeDef* huart)

+{

+  GPIO_InitTypeDef GPIO_InitStruct;

+

+  if (huart->Instance == USART1) {

+    /* Peripheral clock enable */

+    __USART1_CLK_ENABLE();

+    GPIO_InitStruct.Pin = GPIO_PIN_9 | GPIO_PIN_10;

+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;

+    GPIO_InitStruct.Pull = GPIO_PULLUP;

+    GPIO_InitStruct.Speed = GPIO_SPEED_FAST;

+    GPIO_InitStruct.Alternate = GPIO_AF7_USART1;

+    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

+

+    /* NVIC for interrupt mode */

+    HAL_NVIC_SetPriority(USART1_IRQn, 0, 1);

+    HAL_NVIC_EnableIRQ(USART1_IRQn);

+  }

+

+}

+

+void HAL_UART_MspDeInit(UART_HandleTypeDef* huart)

+{

+

+  if (huart->Instance == USART1) {

+    __USART1_CLK_DISABLE();

+    HAL_GPIO_DeInit(GPIOA, GPIO_PIN_9 | GPIO_PIN_10);

+  }

+

+}

diff --git a/src/uart-test/stm32f4xx_it.c b/src/uart-test/stm32f4xx_it.c
new file mode 100644
index 0000000..4dcf0e9
--- /dev/null
+++ b/src/uart-test/stm32f4xx_it.c
@@ -0,0 +1,201 @@
+/**
+  ******************************************************************************
+  * @file    GPIO/GPIO_IOToggle/Src/stm32f4xx_it.c 
+  * @author  MCD Application Team
+  * @version V1.0.1
+  * @date    26-February-2014
+  * @brief   Main Interrupt Service Routines.
+  *          This file provides template for all exceptions handler and 
+  *          peripherals interrupt service routine.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f4xx_it.h"
+#include "stm_init.h"
+
+/** @addtogroup STM32F4xx_HAL_Examples
+  * @{
+  */
+
+/** @addtogroup GPIO_IOToggle
+  * @{
+  */
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+
+/* UART handler declared in "stm_init.h" file */
+//extern UART_HandleTypeDef huart2;
+
+/* Private function prototypes -----------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+
+/******************************************************************************/
+/*            Cortex-M4 Processor Exceptions Handlers                         */
+/******************************************************************************/
+
+/**
+  * @brief   This function handles NMI exception.
+  * @param  None
+  * @retval None
+  */
+void NMI_Handler(void)
+{
+}
+
+/**
+  * @brief  This function handles Hard Fault exception.
+  * @param  None
+  * @retval None
+  */
+void HardFault_Handler(void)
+{
+  /* Go to infinite loop when Hard Fault exception occurs */
+  while (1)
+  {
+  }
+}
+
+/**
+  * @brief  This function handles Memory Manage exception.
+  * @param  None
+  * @retval None
+  */
+void MemManage_Handler(void)
+{
+  /* Go to infinite loop when Memory Manage exception occurs */
+  while (1)
+  {
+  }
+}
+
+/**
+  * @brief  This function handles Bus Fault exception.
+  * @param  None
+  * @retval None
+  */
+void BusFault_Handler(void)
+{
+  /* Go to infinite loop when Bus Fault exception occurs */
+  while (1)
+  {
+  }
+}
+
+/**
+  * @brief  This function handles Usage Fault exception.
+  * @param  None
+  * @retval None
+  */
+void UsageFault_Handler(void)
+{
+  /* Go to infinite loop when Usage Fault exception occurs */
+  while (1)
+  {
+  }
+}
+
+/**
+  * @brief  This function handles SVCall exception.
+  * @param  None
+  * @retval None
+  */
+void SVC_Handler(void)
+{
+}
+
+/**
+  * @brief  This function handles Debug Monitor exception.
+  * @param  None
+  * @retval None
+  */
+void DebugMon_Handler(void)
+{
+}
+
+/**
+  * @brief  This function handles PendSVC exception.
+  * @param  None
+  * @retval None
+  */
+void PendSV_Handler(void)
+{
+}
+
+/**
+  * @brief  This function handles SysTick Handler.
+  * @param  None
+  * @retval None
+  */
+void SysTick_Handler(void)
+{
+  HAL_IncTick();
+}
+
+/******************************************************************************/
+/*                 STM32F4xx Peripherals Interrupt Handlers                   */
+/*  Add here the Interrupt Handler for the used peripheral(s) (PPP), for the  */
+/*  available peripheral interrupt handler's name please refer to the startup */
+/*  file (startup_stm32f4xx.s).                                               */
+/******************************************************************************/
+
+/**
+ * @brief  This function handles UART interrupt request.
+ * @param  None
+ * @retval None
+ * @Note   This function is redefined in "main.h" and related to DMA stream
+ *         used for USART data transmission
+ */
+void USART1_IRQHandler(void)
+{
+  HAL_UART_IRQHandler(&huart1);
+}
+
+/**
+  * @brief  This function handles PPP interrupt request.
+  * @param  None
+  * @retval None
+  */
+/*void PPP_IRQHandler(void)
+{
+}*/
+
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/src/uart-test/stm32f4xx_it.h b/src/uart-test/stm32f4xx_it.h
new file mode 100644
index 0000000..6edba3c
--- /dev/null
+++ b/src/uart-test/stm32f4xx_it.h
@@ -0,0 +1,68 @@
+/**
+  ******************************************************************************
+  * @file    GPIO/GPIO_IOToggle/Inc/stm32f4xx_it.h
+  * @author  MCD Application Team
+  * @version V1.0.1
+  * @date    26-February-2014
+  * @brief   This file contains the headers of the interrupt handlers.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F4xx_IT_H
+#define __STM32F4xx_IT_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+/* Exported macro ------------------------------------------------------------*/
+/* Exported functions ------------------------------------------------------- */
+
+void NMI_Handler(void);
+void HardFault_Handler(void);
+void MemManage_Handler(void);
+void BusFault_Handler(void);
+void UsageFault_Handler(void);
+void SVC_Handler(void);
+void DebugMon_Handler(void);
+void PendSV_Handler(void);
+void SysTick_Handler(void);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F4xx_IT_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/src/uart-test/stm_init.c b/src/uart-test/stm_init.c
new file mode 100644
index 0000000..ad39080
--- /dev/null
+++ b/src/uart-test/stm_init.c
@@ -0,0 +1,268 @@
+/**
+  ******************************************************************************
+  * @file    GPIO/GPIO_IOToggle/Src/main.c
+  * @author  MCD Application Team
+  * @version V1.0.1
+  * @date    26-February-2014
+  * @brief   This example describes how to configure and use GPIOs through
+  *          the STM32F4xx HAL API.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm_init.h"
+
+UART_HandleTypeDef huart1;
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+
+#define UART1_BAUD_RATE 460800
+
+
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+
+static GPIO_InitTypeDef  GPIO_InitStruct;
+
+/* Private function prototypes -----------------------------------------------*/
+static void SystemClock_Config(void);
+static void Error_Handler(void);
+static void MX_GPIO_Init(void);
+static void MX_USART1_UART_Init(void);
+/* Private functions ---------------------------------------------------------*/
+
+/**
+  * @brief  Main program
+  * @param  None
+  * @retval None
+  */
+void stm_init(void)
+{
+ /* Generic STM32 initialization.
+
+    To proceed, 3 steps are required: */
+
+  /* STM32F4xx HAL library initialization:
+       - Configure the Flash prefetch, instruction and Data caches
+       - Configure the Systick to generate an interrupt each 1 msec
+       - Set NVIC Group Priority to 4
+       - Global MSP (MCU Support Package) initialization
+     */
+  HAL_Init();
+
+  /* Configure the system clock */
+  SystemClock_Config();
+
+  /* System interrupt init*/
+  /* Sets the priority grouping field */
+  HAL_NVIC_SetPriorityGrouping(NVIC_PRIORITYGROUP_0);
+  HAL_NVIC_SetPriority(SysTick_IRQn, 0, 0);
+
+  /* Initialize all configured peripherals */
+  MX_GPIO_Init();
+  MX_USART1_UART_Init();
+}
+
+
+/**
+  * @brief  System Clock Configuration
+  *         The system Clock is configured as follow :
+  *            System Clock source            = PLL (HSE)
+  *            SYSCLK(Hz)                     = 42000000
+  *            HCLK(Hz)                       = 42000000
+  *            AHB Prescaler                  = 1
+  *            APB1 Prescaler                 = 1
+  *            APB2 Prescaler                 = 1
+  *            HSI Frequency(Hz)              = 16000000
+  *            PLL_M                          = 8
+  *            PLL_N                          = 336
+  *            PLL_P                          = 8
+  *            PLL_Q                          = 7 (unused)
+  *            VDD(V)                         = 3.3
+  *            Main regulator output voltage  = Scale2 mode
+  *            Flash Latency(WS)              = 1
+  * @param  None
+  * @retval None
+  */
+static void SystemClock_Config(void)
+{
+  RCC_ClkInitTypeDef RCC_ClkInitStruct;
+  RCC_OscInitTypeDef RCC_OscInitStruct;
+
+  /* Enable Power Control clock */
+  __PWR_CLK_ENABLE();
+
+  /* The voltage scaling allows optimizing the power consumption when the device is
+     clocked below the maximum system frequency, to update the voltage scaling value
+     regarding system frequency refer to product datasheet.  */
+  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+  /* Enable HSE Oscillator and activate PLL with HSE as source.
+   *
+   * With 8 MHz HSE oscillator, M=/8, N=*336, P=/8 gives 42 MHz SYSCLK.
+   * Divider Q is unused in this configuration.
+   */
+  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+  RCC_OscInitStruct.PLL.PLLM = 8;
+  RCC_OscInitStruct.PLL.PLLN = 336;
+  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV8;
+  RCC_OscInitStruct.PLL.PLLQ = 7;
+  if(HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
+  {
+    Error_Handler();
+  }
+
+  /* Select PLL as system clock source */
+  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK;
+  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;		/* AHB prescaler */
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;		/* APB1 prescaler /1 gives 42 MHz APB1 */
+  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;		/* APB2 prescaler /1 gives 42 MHz APB2 */
+  if(HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1) != HAL_OK)
+  {
+    Error_Handler();
+  }
+
+  /* Set up HSE sourced (8 MHz) MCO1 */
+  HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1);
+
+  /* Set up SYSCLK sourced (42 MHz) MCO2 */
+  HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_1);
+}
+
+
+/** Configure pins as
+
+     PB12   ------> GREEN LED
+     PB13   ------> YELLOW LED
+     PB14   ------> GREEN lED
+     PB15   ------> BLUE LED
+     PC9    ------> MCO_2
+     PA8    ------> MCO_1
+*/
+void MX_GPIO_Init(void)
+{
+  /* GPIO Ports Clock Enable */
+  __GPIOA_CLK_ENABLE();
+  __GPIOB_CLK_ENABLE();
+  __GPIOC_CLK_ENABLE();
+
+  /*Configure LED GPIO pins PB12==red, PB13==yellow, PB14==green, PB15==blue */
+  GPIO_InitStruct.Pin = GPIO_PIN_12 | GPIO_PIN_13 | GPIO_PIN_14 | GPIO_PIN_15;
+  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
+  HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
+  /*Configure GPIO pin : PC9 (RCC_MCO_2) */
+  GPIO_InitStruct.Pin = GPIO_PIN_9;
+  GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
+  GPIO_InitStruct.Alternate = GPIO_AF0_MCO;
+  HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
+
+  /*Configure GPIO pin : PA8 (RCC_MCO_1) */
+  GPIO_InitStruct.Pin = GPIO_PIN_8;
+  GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
+  GPIO_InitStruct.Alternate = GPIO_AF0_MCO;
+  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+}
+
+/* USART1 init function
+ *
+ * USART1 uses PA9 and PA10.
+ */
+void MX_USART1_UART_Init(void)
+{
+
+  huart1.Instance = USART1;
+  huart1.Init.BaudRate = UART1_BAUD_RATE;
+  huart1.Init.WordLength = UART_WORDLENGTH_8B;
+  huart1.Init.StopBits = UART_STOPBITS_1;
+  huart1.Init.Parity = UART_PARITY_NONE;
+  huart1.Init.Mode = UART_MODE_TX_RX;
+  huart1.Init.HwFlowCtl = UART_HWCONTROL_NONE;
+  huart1.Init.OverSampling = UART_OVERSAMPLING_16;
+
+  if(HAL_UART_Init(&huart1) != HAL_OK) {
+    /* Initialization Error */
+    Error_Handler();
+  }
+
+}
+
+/**
+  * @brief  This function is executed in case of error occurrence.
+  * @param  None
+  * @retval None
+  */
+static void Error_Handler(void)
+{
+  HAL_GPIO_WritePin(LED_PORT, LED_RED, GPIO_PIN_SET);
+  while(1) { ; }
+}
+
+#ifdef  USE_FULL_ASSERT
+
+/**
+  * @brief  Reports the name of the source file and the source line number
+  *         where the assert_param error has occurred.
+  * @param  file: pointer to the source file name
+  * @param  line: assert_param error line source number
+  * @retval None
+  */
+void assert_failed(uint8_t* file, uint32_t line)
+{
+  /* User can add his own implementation to report the file name and line number,
+     ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
+
+  /* Infinite loop */
+  while (1)
+  {
+  }
+}
+#endif
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/src/uart-test/stm_init.h b/src/uart-test/stm_init.h
new file mode 100644
index 0000000..e1cdfb8
--- /dev/null
+++ b/src/uart-test/stm_init.h
@@ -0,0 +1,16 @@
+#ifndef __STM_INIT_H
+#define __STM_INIT_H
+
+#include "stm32f4xx_hal.h"
+
+#define LED_PORT	GPIOB
+#define LED_RED		GPIO_PIN_12
+#define LED_YELLOW	GPIO_PIN_13
+#define LED_GREEN	GPIO_PIN_14
+#define LED_BLUE	GPIO_PIN_15
+
+extern UART_HandleTypeDef huart1;
+extern void stm_init(void);
+
+
+#endif /* __STM_INIT_H */
diff --git a/src/uart-test/system_stm32f4xx.c b/src/uart-test/system_stm32f4xx.c
new file mode 100644
index 0000000..3068a90
--- /dev/null
+++ b/src/uart-test/system_stm32f4xx.c
@@ -0,0 +1,270 @@
+/**
+  ******************************************************************************
+  * @file    system_stm32f4xx.c
+  * @author  MCD Application Team
+  * @version V1.0.1
+  * @date    26-February-2014
+  * @brief   CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
+  *
+  *   This file provides two functions and one global variable to be called from 
+  *   user application:
+  *      - SystemInit(): This function is called at startup just after reset and 
+  *                      before branch to main program. This call is made inside
+  *                      the "startup_stm32f4xx.s" file.
+  *
+  *      - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
+  *                                  by the user application to setup the SysTick 
+  *                                  timer or configure other parameters.
+  *                                     
+  *      - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
+  *                                 be called whenever the core clock is changed
+  *                                 during program execution.
+  *
+  *
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT 2014 STMicroelectronics</center></h2>
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */
+
+/** @addtogroup CMSIS
+  * @{
+  */
+
+/** @addtogroup stm32f4xx_system
+  * @{
+  */  
+  
+/** @addtogroup STM32F4xx_System_Private_Includes
+  * @{
+  */
+
+#include "stm32f4xx_hal.h"
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F4xx_System_Private_Defines
+  * @{
+  */
+
+/************************* Miscellaneous Configuration ************************/
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+     Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET  0x00 /*!< Vector Table base offset field. 
+                                   This value must be a multiple of 0x200. */
+/******************************************************************************/
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F4xx_System_Private_Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F4xx_System_Private_Variables
+  * @{
+  */
+  /* This variable is updated in three ways:
+      1) by calling CMSIS function SystemCoreClockUpdate()
+      2) by calling HAL API function HAL_RCC_GetHCLKFreq()
+      3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency 
+         Note: If you use this function to configure the system clock; then there
+               is no need to call the 2 first functions listed above, since SystemCoreClock
+               variable is updated automatically.
+  */
+  uint32_t SystemCoreClock = 16000000;
+  __I uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F4xx_System_Private_Functions
+  * @{
+  */
+
+/**
+  * @brief  Setup the microcontroller system
+  *         Initialize the FPU setting, vector table location and External memory 
+  *         configuration.
+  * @param  None
+  * @retval None
+  */
+void SystemInit(void)
+{
+  /* FPU settings ------------------------------------------------------------*/
+  #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+    SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2));  /* set CP10 and CP11 Full Access */
+  #endif
+  /* Reset the RCC clock configuration to the default reset state ------------*/
+  /* Set HSION bit */
+  RCC->CR |= (uint32_t)0x00000001;
+
+  /* Reset CFGR register */
+  RCC->CFGR = 0x00000000;
+
+  /* Reset HSEON, CSSON and PLLON bits */
+  RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+  /* Reset PLLCFGR register */
+  RCC->PLLCFGR = 0x24003010;
+
+  /* Reset HSEBYP bit */
+  RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+  /* Disable all interrupts */
+  RCC->CIR = 0x00000000;
+
+  /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+  SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+  SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+}
+
+/**
+   * @brief  Update SystemCoreClock variable according to Clock Register Values.
+  *         The SystemCoreClock variable contains the core clock (HCLK), it can
+  *         be used by the user application to setup the SysTick timer or configure
+  *         other parameters.
+  *           
+  * @note   Each time the core clock (HCLK) changes, this function must be called
+  *         to update SystemCoreClock variable value. Otherwise, any configuration
+  *         based on this variable will be incorrect.         
+  *     
+  * @note   - The system frequency computed by this function is not the real 
+  *           frequency in the chip. It is calculated based on the predefined 
+  *           constant and the selected clock source:
+  *             
+  *           - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
+  *                                              
+  *           - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
+  *                          
+  *           - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**) 
+  *             or HSI_VALUE(*) multiplied/divided by the PLL factors.
+  *         
+  *         (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
+  *             16 MHz) but the real value may vary depending on the variations
+  *             in voltage and temperature.   
+  *    
+  *         (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
+  *              depends on the application requirements), user has to ensure that HSE_VALUE
+  *              is same as the real frequency of the crystal used. Otherwise, this function
+  *              may have wrong result.
+  *                
+  *         - The result of this function could be not correct when using fractional
+  *           value for HSE crystal.
+  *     
+  * @param  None
+  * @retval None
+  */
+void SystemCoreClockUpdate(void)
+{
+  uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
+  
+  /* Get SYSCLK source -------------------------------------------------------*/
+  tmp = RCC->CFGR & RCC_CFGR_SWS;
+
+  switch (tmp)
+  {
+    case 0x00:  /* HSI used as system clock source */
+      SystemCoreClock = HSI_VALUE;
+      break;
+    case 0x04:  /* HSE used as system clock source */
+      SystemCoreClock = HSE_VALUE;
+      break;
+    case 0x08:  /* PLL used as system clock source */
+
+      /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
+         SYSCLK = PLL_VCO / PLL_P
+         */    
+      pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
+      pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
+      
+      if (pllsource != 0)
+      {
+        /* HSE used as PLL clock source */
+        pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
+      }
+      else
+      {
+        /* HSI used as PLL clock source */
+        pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
+      }
+
+      pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
+      SystemCoreClock = pllvco/pllp;
+      break;
+    default:
+      SystemCoreClock = HSI_VALUE;
+      break;
+  }
+  /* Compute HCLK frequency --------------------------------------------------*/
+  /* Get HCLK prescaler */
+  tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
+  /* HCLK frequency */
+  SystemCoreClock >>= tmp;
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+  
+/**
+  * @}
+  */    
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/