1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
|
//======================================================================
//
// core_selector.v
// ---------------
// Top level wrapper that creates the Cryptech coretest system.
// The wrapper contains instances of external interface, coretest
// and the core to be tested. And if more than one core is
// present the wrapper also includes address and data muxes.
//
//
// Authors: Joachim Strombergson, Paul Selkirk, Pavel Shatov
// Copyright (c) 2014-2015, NORDUnet A/S All rights reserved.
//
// Redistribution and use in source and binary forms, with or without
// modification, are permitted provided that the following conditions are
// met:
// - Redistributions of source code must retain the above copyright notice,
// this list of conditions and the following disclaimer.
//
// - Redistributions in binary form must reproduce the above copyright
// notice, this list of conditions and the following disclaimer in the
// documentation and/or other materials provided with the distribution.
//
// - Neither the name of the NORDUnet nor the names of its contributors may
// be used to endorse or promote products derived from this software
// without specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
// IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
// TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
// PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
// HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
// SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
// TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
// PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
// LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
// NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
// SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
//
//======================================================================
module core_selector
(
input wire sys_clk,
input wire sys_rst,
input wire sys_ena,
input wire [13 : 0] sys_eim_addr,
input wire sys_eim_wr,
input wire sys_eim_rd,
output wire [31 : 0] sys_read_data,
input wire [31 : 0] sys_write_data
);
/* In this memory segment (HASHES) we have 14 address bits. Every core has
* 8-bit internal address space, so we can have up to 2^(14-8) = 64 cores here.
*
* Core #0 is not an actual HASH core, but a set of board-level (global)
* registers, that can be used to get information about hardware (board
* type, bitstream version and so on).
*
* So far we have three cores: SHA-1, SHA-256 and SHA-512.
*/
/*********************************************************
* To add new HASH core named XXX follow the steps below *
*********************************************************
*
* 1. Add corresponding `define under "List of Available Cores", this will
* allow users to exclude your core from implementation to save some
* slices in case they don't need it.
*
* `define USE_CORE_XXX
*
*
* 2. Choose address of your new core and add corresponding line under
* "Core Address Table". Core addresses can be in the range from 1 to 63
* inclusively. Core address 0 is reserved for a page of global
* registers and must not be used.
*
* localparam CORE_ADDR_XXX = 6'dN;
*
*
* 3. Add instantiation of your new core after all existing cores
* surrounded by conditional synthesis directives.
* You also need a 32-bit output (read data) bus for your core and an
* enable flag. Note that sys_rst in an active-high sync reset signal.
*
* `ifdef USE_CORE_XXX
* wire [31: 0] read_data_xxx;
* wire enable_xxx = sys_ena && (addr_core_num == CORE_ADDR_XXX);
* xxx xxx_inst
* (
* .clk(sys_clk),
* .reset_n(~sys_rst),
* .cs(enable_xxx & (sys_eim_rd | sys_eim_wr)),
* .we(sys_eim_wr),
* .address(addr_core_reg),
* .write_data(sys_write_data),
* .read_data(read_data_xxx),
* .error()
* );
* `endif
*
*
* 4. Add previously created data bus to "Output (Read Data) Multiplexor"
* in the end of this file.
*
* `ifdef USE_CORE_XXX
* CORE_ADDR_XXX:
* sys_read_data_mux = read_data_xxx;
* `endif
*
*/
//----------------------------------------------------------------
// Address Decoder
//----------------------------------------------------------------
wire [ 5: 0] addr_core_num = sys_eim_addr[13: 8]; // upper 6 bits specify core being addressed
wire [ 7: 0] addr_core_reg = sys_eim_addr[ 7: 0]; // lower 8 bits specify register offset in core
/* We can comment following lines to exclude cores from implementation
* in case we run out of slices.
*/
//----------------------------------------------------------------
// List of Available Cores
//----------------------------------------------------------------
`define USE_CORE_SHA1
`define USE_CORE_SHA256
`define USE_CORE_SHA512
//----------------------------------------------------------------
// Core Address Table
//----------------------------------------------------------------
localparam CORE_ADDR_GLOBAL_REGS = 6'd0;
localparam CORE_ADDR_SHA1 = 6'd1;
localparam CORE_ADDR_SHA256 = 6'd2;
localparam CORE_ADDR_SHA512 = 6'd3;
//----------------------------------------------------------------
// Global Registers
//----------------------------------------------------------------
wire [31: 0] read_data_global;
wire enable_global = sys_ena && (addr_core_num == CORE_ADDR_GLOBAL_REGS);
novena_regs novena_regs_inst
(
.clk(sys_clk),
.rst(sys_rst),
.cs(enable_global & (sys_eim_rd | sys_eim_wr)),
.we(sys_eim_wr),
.address(addr_core_reg),
.write_data(sys_write_data),
.read_data(read_data_global)
);
//----------------------------------------------------------------
// SHA-1
//----------------------------------------------------------------
`ifdef USE_CORE_SHA1
wire [31: 0] read_data_sha1;
wire enable_sha1 = sys_ena && (addr_core_num == CORE_ADDR_SHA1);
sha1 sha1_inst
(
.clk(sys_clk),
.reset_n(~sys_rst),
.cs(enable_sha1 & (sys_eim_rd | sys_eim_wr)),
.we(sys_eim_wr),
.address(addr_core_reg),
.write_data(sys_write_data),
.read_data(read_data_sha1)
);
`endif
//----------------------------------------------------------------
// SHA-256
//----------------------------------------------------------------
`ifdef USE_CORE_SHA256
wire [31: 0] read_data_sha256;
wire enable_sha256 = sys_ena && (addr_core_num == CORE_ADDR_SHA256);
sha256 sha256_inst
(
.clk(sys_clk),
.reset_n(~sys_rst),
.cs(enable_sha256 & (sys_eim_rd | sys_eim_wr)),
.we(sys_eim_wr),
.address(addr_core_reg),
.write_data(sys_write_data),
.read_data(read_data_sha256)
);
`endif
//----------------------------------------------------------------
// SHA-512
//----------------------------------------------------------------
`ifdef USE_CORE_SHA512
wire [31: 0] read_data_sha512;
wire enable_sha512 = sys_ena && (addr_core_num == CORE_ADDR_SHA512);
sha512 sha512_inst
(
.clk(sys_clk),
.reset_n(~sys_rst),
.cs(enable_sha512 & (sys_eim_rd | sys_eim_wr)),
.we(sys_eim_wr),
.address(addr_core_reg),
.write_data(sys_write_data),
.read_data(read_data_sha512)
);
`endif
//----------------------------------------------------------------
// Output (Read Data) Multiplexor
//----------------------------------------------------------------
reg [31: 0] sys_read_data_mux;
assign sys_read_data = sys_read_data_mux;
always @*
//
case (addr_core_num)
//
CORE_ADDR_GLOBAL_REGS:
sys_read_data_mux = read_data_global;
`ifdef USE_CORE_SHA1
CORE_ADDR_SHA1:
sys_read_data_mux = read_data_sha1;
`endif
`ifdef USE_CORE_SHA256
CORE_ADDR_SHA256:
sys_read_data_mux = read_data_sha256;
`endif
`ifdef USE_CORE_SHA512
CORE_ADDR_SHA512:
sys_read_data_mux = read_data_sha512;
`endif
//
default:
sys_read_data_mux = {32{1'b0}};
//
endcase
endmodule
//======================================================================
// EOF core_selector.v
//======================================================================
|
