aboutsummaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rwxr-xr-xsrc/sw/entropy_tester.py64
1 files changed, 47 insertions, 17 deletions
diff --git a/src/sw/entropy_tester.py b/src/sw/entropy_tester.py
index 1b0e19d..57c0562 100755
--- a/src/sw/entropy_tester.py
+++ b/src/sw/entropy_tester.py
@@ -67,7 +67,7 @@ STOP_BITS = 1
# Delay times.
PROC_DELAY_TIME = 0.001
-COMM_DELAY_TIME = 0.01
+COMM_DELAY_TIME = 0.005
# Verbose operation on/off
@@ -80,6 +80,10 @@ READ_CMD = '\x10'
WRITE_CMD = '\x11'
UART_ADDR_PREFIX = '\x00'
+UART_ADDR_NAME0 = '\x00'
+UART_ADDR_NAME1 = '\x01'
+UART_ADDR_TYPE = '\x02'
+UART_ADDR_VERSION = '\x03'
UART_ADDR_BIT_RATE = '\x10'
UART_ADDR_DATA_BITS = '\x11'
UART_ADDR_STOP_BITS = '\x12'
@@ -182,15 +186,24 @@ def read_word(prefix, addr, ser):
# read_rng1_rng2()
#-------------------------------------------------------------------
def read_rng1_rng2(ser):
+ if VERBOSE:
+ print "Reading rng1 and rng2 three times."
+
for i in range(3):
read_word(BPENT_ADDR_PREFIX, BPENT_ADDR_RD_RNG1_RNG2, ser)
#-------------------------------------------------------------------
# read_n_data()
+#
+# Note we do a lot of read ops here.
#-------------------------------------------------------------------
def read_n_data(ser):
- for i in range(10):
+ n = int(1E6)
+ if VERBOSE:
+ print "Reading n vector %d times." % n
+
+ for i in range(n):
read_word(BPENT_ADDR_PREFIX, BPENT_ADDR_RD_N, ser)
@@ -198,11 +211,27 @@ def read_n_data(ser):
# read_p_data()
#-------------------------------------------------------------------
def read_p_data(ser):
- for i in range(10):
+ n = 10
+ if VERBOSE:
+ print "Reading p vector %d times." % n
+
+ for i in range(n):
read_word(BPENT_ADDR_PREFIX, BPENT_ADDR_RD_P, ser)
#-------------------------------------------------------------------
+# read_uart()
+#
+# We try to read from the uart to get some read ops working.
+#-------------------------------------------------------------------
+def read_uart(ser):
+ read_word(UART_ADDR_PREFIX, UART_ADDR_NAME0, ser)
+ read_word(UART_ADDR_PREFIX, UART_ADDR_NAME1, ser)
+ read_word(UART_ADDR_PREFIX, UART_ADDR_TYPE, ser)
+ read_word(UART_ADDR_PREFIX, UART_ADDR_VERSION, ser)
+
+
+#-------------------------------------------------------------------
# main()
#
# Parse any arguments and run the tests.
@@ -228,18 +257,18 @@ def main():
sys.exit(1)
# Try and switch baud rate in the FPGA and then here.
-# bit_rate_high = chr((BIT_RATE2 >> 8) & 0xff)
-# bit_rate_low = chr(BIT_RATE2 & 0xff)
-#
-# if VERBOSE:
-# print("Changing to new baud rate.")
-# print("Baud rate: %d" % BAUD_RATE2)
-# print("Bit rate high byte: 0x%02x" % ord(bit_rate_high))
-# print("Bit rate low byte: 0x%02x" % ord(bit_rate_low))
-#
-# write_serial_bytes([SOC, WRITE_CMD, UART_ADDR_PREFIX, UART_ADDR_BIT_RATE,
-# '\x00', '\x00', bit_rate_high, bit_rate_low, EOC], ser)
-# ser.baudrate=BAUD_RATE2
+ bit_rate_high = chr((BIT_RATE2 >> 8) & 0xff)
+ bit_rate_low = chr(BIT_RATE2 & 0xff)
+
+ if VERBOSE:
+ print("Changing to new baud rate.")
+ print("Baud rate: %d" % BAUD_RATE2)
+ print("Bit rate high byte: 0x%02x" % ord(bit_rate_high))
+ print("Bit rate low byte: 0x%02x" % ord(bit_rate_low))
+
+ write_serial_bytes([SOC, WRITE_CMD, UART_ADDR_PREFIX, UART_ADDR_BIT_RATE,
+ '\x00', '\x00', bit_rate_high, bit_rate_low, EOC], ser)
+ ser.baudrate=BAUD_RATE2
try:
my_thread = threading.Thread(target=read_serial_thread, args=(ser,))
@@ -250,12 +279,13 @@ def main():
my_thread.daemon = True
my_thread.start()
+ # Test the communication by reading name etc from uart.
+ read_uart(ser)
# Perform RNG read ops.
read_rng1_rng2(ser)
- read_n_data(ser)
read_p_data(ser)
-
+ read_n_data(ser)
# Exit nicely.
time.sleep(50 * COMM_DELAY_TIME)