/*
* bootloader.c
* ------------
* Bootloader to either install new firmware received from the MGMT UART,
* or jump to previously installed firmware.
*
* Copyright (c) 2016, NORDUnet A/S All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are
* met:
* - Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
*
* - Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* - Neither the name of the NORDUnet nor the names of its contributors may
* be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
* IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
* PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
* TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
* PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
* LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
* NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#include "stm-init.h"
#include "stm-led.h"
#include "stm-uart.h"
#include "stm-fmc.h"
#include "dfu.h"
/* stub these out to avoid linker error */
void fpgacfg_init(void) { }
void sdram_init(void) { }
void *hal_allocate_static_memory(const size_t size) { return 0; }
/* Linker symbols are strange in C. Make regular pointers for sanity. */
__IO uint32_t *dfu_control = &CRYPTECH_DFU_CONTROL;
__IO uint32_t *dfu_firmware = &CRYPTECH_FIRMWARE_START;
/* The first word in the firmware is an address to the stack (msp) */
__IO uint32_t *dfu_msp_ptr = &CRYPTECH_FIRMWARE_START;
/* The second word in the firmware is a pointer to the code
* (points at the Reset_Handler from the linker script).
*/
__IO uint32_t *dfu_code_ptr = &CRYPTECH_FIRMWARE_START + 1;
typedef void (*pFunction)(void);
/* called from Reset_Handler */
void check_early_dfu_jump(void)
{
/* Check if we've just rebooted in order to jump to the firmware. */
if (*dfu_control == HARDWARE_EARLY_DFU_JUMP) {
*dfu_control = 0;
pFunction loaded_app = (pFunction) *dfu_code_ptr;
/* Set the stack pointer to the correct one for the firmware */
__set_MSP(*dfu_msp_ptr);
/* Set the Vector Table Offset Register */
SCB->VTOR = (uint32_t) dfu_firmware;
loaded_app();
while (1);
}
}
int should_dfu()
{
int i;
uint8_t rx = 0;
/* While blinking the blue LED for 5 seconds, see if we receive a CR on the MGMT UART.
* We've discussed also requiring one or both of the FPGA config jumpers installed
* before allowing DFU of the STM32 - that check could be done here.
*/
led_on(LED_BLUE);
for (i = 0; i < 50; i++) {
HAL_Delay(100);
led_toggle(LED_BLUE);
if (uart_recv_char(&rx, 0) == HAL_OK) {
if (rx == 13) return 1;
}
}
return 0;
}
/* Sleep for specified number of seconds -- used after bad PIN. */
void hal_sleep(const unsigned seconds) { HAL_Delay(seconds * 1000); }
int main(void)
{
int status;
stm_init();
uart_send_string("\r\n\r\nThis is the bootloader speaking...");
if (should_dfu()) {
led_off(LED_BLUE);
if ((status = dfu_receive_firmware()) != 0) {
/* Upload of new firmware failed, reboot after lighting the red LED
* for three seconds.
*/
led_off(LED_BLUE);
led_on(LED_RED);
uart_send_string("dfu_receive_firmware failed: ");
uart_send_hex(status, 2);
uart_send_string("\r\n\r\nRebooting in three seconds\r\n");
HAL_Delay(3000);
HAL_NVIC_SystemReset();
while (1) {};
}
}
/* Set dfu_control to the magic value that will cause the us to call do_early_dfu_jump
* after rebooting back into this main() function.
*/
*dfu_control = HARDWARE_EARLY_DFU_JUMP;
uart_send_string("loading firmware\r\n\r\n");
/* De-initialize hardware by rebooting */
HAL_NVIC_SystemReset();
while (1) {};
}
id='n49' href='#n49'>49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
|