STM32 software for dev-bridge/Alpha board ========================================= The dev-bridge board is a daughterboard for the Novena, which talks to the Novena's FPGA through the high-speed expansion connector. The Alpha board is a stand-alone board with an Artix-7 FPGA, a STM32 Cortex-M4 microcontroller, two USB interfaces etc. See user/ft/stm32-dev-bridge/hardware/rev01 for schematics of the bridge board. There will be more information on the wiki shortly. Copyrights ========== The license for all work done on this in the CrypTech project is a 3-clause BSD license (see LICENSE.txt for details). Some files have been generated using the STMicroelectronics initialization code generator STM32CubeMX and thus have additional copyright header(s). The "Noise generator" and "Amplifier" parts of the circuit diagram are copied from Benedikt Stockebrand's ARRGH project. ARRGH copyright statement is included in LICENSE.txt. A stripped down copy of the ARM CMSIS library version 3.20 is included in the Drivers/CMSIS/ directory. Unused parts (and documentation etc.) have been removed, but every attempt have been made to keep any licensing information intact. See in particular the file Drivers/CMSIS/CMSIS END USER LICENCE AGREEMENT.pdf. A full copy of the STM32F4xx HAL Drivers is included in the Drivers/STM32F4xx_HAL_Driver/ directory. Building ======== The following packages need to be installed (on Ubuntu 14.04): apt-get install gcc-arm-none-eabi gdb-arm-none-eabi openocd To build the source code, issue "make" from the top level directory (where this file is). The first time, this will build the complete STM CMSIS library. A subsequent "make clean" will *not* clean away the CMSIS library, but a "make distclean" will. Installing ========== Do "bin/flash-target" from the top level directory (where this file is) to flash a built image into the microcontroller. See the section ST-LINK below for information about the actual hardware programming device needed. Example loading the bootloader and the led-test firmware to get some LEDs flashing: $ make bootloader board-test $ ./bin/flash-target projects/board-test/led-test $ ./bin/flash-target projects/bootloader/bootloader At this point, the STM32 will reset into the bootloader which flashes the blue LED five times in one second, and then execution of the LED test firmware will begin. The LED test firmware will flash the green, yellow, red and blue LEDs in order until the end of time. Once the bootloader is installed, regular firmware can be loaded without an ST-LINK cable like this: $ ./bin/dfu projects/board-test/led-test.bin Then reboot the Alpha board. ST-LINK ======= To program the MCU, an ST-LINK adapter is used. The cheapest way to get one is to buy an evaluation board with an ST-LINK integrated, and pinouts to program external chips. This should work with any evaluation board from STM; we have tested with STM32F4DISCOVERY (with ST-LINK v2.0) and NUCLEO-F411RE (with ST-LINK v2.1). The ST-LINK programming pins is called J1 and is near the CrypTech logo printed on the circuit board. The pin-outs is shown on the circuit board (follow the thin white line from J1 to the white box with STM32_SWD written in it). From left to right, the pins are 3V3, CLK, GND, I/O, NRST and N/C This matches the pin-out on the DISCO and NUCLEO boards we have tried. First remove the pair of ST-LINK jumpers (CN4 on the DISCO, CN2 on the NUCLEO). Then find the 6-pin SWD header on the left of the STM board (CN2 on the DISCO, CN4 on the NUCLEO), and connect them to the Alpha board: NUCLEO / DISCO CRYPTECH ALPHA -------------- -------------- * 1 VDD_TARGET <-> 3V3 * 2 SWCLK / T_JTCK <-> CLK * 3 GND <-> GND * 4 SWDIO / T_JTMS <-> IO * 5 T_NRST / NRST <-> NRST N/C (pin 6) means Not Connected. The Alpha board should be powered on before attempting to flash it. Debugging the firmware ====================== This site shows several ways to use various debuggers to debug the firmware in an STM32: http://fun-tech.se/stm32/OpenOCD/gdb.php There is a shell script called 'bin/debug' that starts an OpenOCD server and GDB. Example: $ ./bin/debug projects/board-test/led-test Once in GDB, issue "monitor reset halt" to reset the STM32 before debugging. Remember that the first code to run will be the bootloader, but if you do e.g. "break main" and "continue" you will end up in led-test main() after the bootloader has jumped there.